Skip to content

Bambu Lab A2L

Not enough owners for a score yet. Here's what they say so far. Good time to buy.

Bambu Lab A2L

2 of 5 owners · 3 more and the score goes live.

Own one? Tap your score:
$439 was $469
6% offLowest in 90 days
Buy at Bambu Lab

Price checked Nov 9 on the official US store.

Owner reviews 2 Rate it (10 seconds)

Reviewers earn Spools (site points) for any review, good or bad. Spools never change a score.

Not enough owner reviews for an overall owner rating yet: 2 of 5. Every rating is shown below as it comes in. Own one? Add yours.

V
VirtuconEarned Spools November 9, 2026
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 10
Recommends this

10/10 and would buy again

Owned 1 to 6 months · Biggest problem: not knowing what to make on it, its so much bigger I keep forgetting I have the capacity

What I liked:

What I didn't like:

Comments (0)

P
PeterBEarned Spools November 9, 2026
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 10
Recommends this

10/10 and would buy again

Owned 1 to 6 months

What I liked:

What I didn't like:

Comments (0)

Owner wall

Own one? Add yours

No verified owners yet. Post a photo of yours with your code and be the first on the wall.

Price history

Official US store, checked weekly

Good time to buy. Now $439. At or near the lowest price we have tracked. Tracked since Jun 2026.

$439 now, $30 below the median ($469)
$469 JunJulAugSepOctNov $469 JulSepNov
Each week's price against the median price, lightly smoothed. Median $469, lowest $439 (week of Nov 16), highest $469, now $439 (−$30 vs median). 21 of 25 weeks are filled from launch announcements, brand sale emails or dated deal reports rather than our own store checks; hover a week to see which. Reported sales are assumed to last two weeks unless we know otherwise.
Weekly price
Week ofLowest pricevs medianSource
Jun 1, 2026$469$0launch price
Jun 8, 2026$469$0launch price
Jun 15, 2026$469$0launch price
Jun 22, 2026$469$0launch price
Jun 29, 2026$469$0launch price
Jul 6, 2026$469$0launch price
Jul 13, 2026$469$0launch price
Jul 20, 2026$469$0launch price
Jul 27, 2026$469$0launch price
Aug 3, 2026$469$0launch price
Aug 10, 2026$469$0launch price
Aug 17, 2026$469$0launch price
Aug 24, 2026$469$0launch price
Aug 31, 2026$469$0launch price
Sep 7, 2026$469$0launch price
Sep 14, 2026$469$0launch price
Sep 21, 2026$469$0launch price
Sep 28, 2026$469$0launch price
Oct 5, 2026$469$0launch price
Oct 12, 2026$469$0launch price
Oct 19, 2026$469$0launch price
Oct 26, 2026$439−$30store check
Nov 2, 2026$439−$30store check
Nov 9, 2026$439−$30store check
Nov 16, 2026$439−$30store check

Known issues 2

Report an issue

From brand advisories, owner forums and reviews, with sources on each. Newest first. Tap one for what happens and what fixes it.

  • Medium AMS lite pauses for stuck filament that is not stuck Last reported Nov 2026

    A2L owners report the AMS lite pausing prints every hour or two, sometimes every few minutes, saying the filament in a slot is stuck when it feeds fine. Some also see it unload and reload the same spool during single-color prints. Several owners notice it most when a spool is nearly empty (about 100 to 150 g left) or with some third-party PETG.

    What fixes it: No confirmed fix. One owner stopped it by swapping to a fresh spool, and a forum moderator suggests checking that the PTFE tubes are pushed fully in. Restarting the printer helped one owner for a while.

    From public reports: forum.bambulab.com · Confirm or add a fix

  • Low Hotend fan is loud with a high-pitched whine Last reported Oct 2026

    Owners running the A2L next to an A1 say its hotend cooling fan is much louder, with a high-pitched whine; one measured about 60 dB at 15 cm against 45 dB for the A1. Some also hear coil whine from the power supply when the printer is idle. One owner says Bambu support told them the fan is louder than the A1's by design and that noise reduction is planned in future software.

    What fixes it: One owner got a replacement fan from support that was about 10 dB quieter at 1 m. Others use a printed fan cover from MakerWorld. For idle whine, owners switch the printer off when not printing.

    From public reports: forum.bambulab.com, forum.bambulab.com · Confirm or add a fix

Specs

The A2L is a large-format bed slinger that scales the A1 formula up to a roughly 330 mm build area, with full auto calibration and an optional cutting/plotter module. It suits beginners and hobbyists who mostly print PLA and PETG and want big parts or cosplay pieces on a budget.

330 × 320 × 325 mmbuild volume
Bed slinger, open frameformat
300 °Cmax nozzle
80 °Cmax bed
None (open frame)chamber
500 mm/smax speed
1toolheads
June 2026released
What the press said · 9.0 from 1 press outlet · Read them

What reviewers say 9.0 from 1

How scores work
  • 9.0 Tom's HardwareA high quality, supersized take on the A1 with a bigger bed and a few upgrades, a good … 4.5/5 · Jun 2026

    A high quality, supersized take on the A1 with a bigger bed and a few upgrades, a good fit for makers who want the Bambu ecosystem without paying for CoreXY. Editor's Choice pick.

    • Fast printing
    • Quick-change nozzle and reliable auto leveling
    • Optional blade cutter for crafts
    • AMS wastes a lot of filament
    • Vibrations at speed can shake light tables

    Read the full review on Tom's Hardware · by Denise Bertacchi