Skip to content

Bambu Lab H3C

Owners like it.

Bambu Lab H3C

9.6from 5 owners
5/25

Early read. Firms up at 25 owners.

$2,499
Buy at Bambu Lab

Price checked Nov 3 on the official US store.

Rate yours

Owner reviews 5 Rate it (10 seconds)

Reviewers earn Spools (site points) for any review, good or bad. Spools never change a score.

O
owner-88673Earned Spools November 16, 2026
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 10
Recommends this

10/10 and would buy again

Owned less than a month

What I liked:

What I didn't like:

Comments (0)

V
VirtuconEarned Spools November 14, 2026 (Edited)
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 9
Recommends this

Get in Mah Belly! H3C Review

Owned less than a month · Biggest problem: A couple support fails on different models. Due to it tall height and my low basement ceiling, I was forced to repurpose an old end table.

What I liked:

Fat Bastard has outstanding print quality, and I'm really enjoying the CMYKW system. I've only completed a few prints with it so far, and it takes some getting used to, but when it works, the results look fantastic. It's a fantastic machine, and I really wish I could justify owning more than one. At this point, I'd seriously consider selling every printer I own except my X2D and replacing them with H3Cs.

What I didn't like:

I'm still not completely sold on the light gray enclosure, although it's growing on me. The height is another challenge. I ended up putting it on an old end table because of its size. The IKEA LACK works perfectly, by the way. I've also had a few issues with failed supports, even after tweaking settings. I've tried printing a Dogman for my son three times without success. I'll keep trying. A few minor complaints, but overall, this big beast is a keeper. Yeah, baby!

View In-Depth Breakdown

Comments (0)

M
mleppelmanEarned Spools November 9, 2026 (Edited)
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 10
Recommends this

10/10 and would buy again

Owned less than a month

What I liked:

I have had this printer for 2 days and I love it.

What I didn't like:

To tall

Comments (0)

M
MaxdepoesGamesEarned Spools November 9, 2026 (Edited)
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 9
Recommends this

9/10 and would buy again

Owned less than a month · Biggest problem: It's a little to big but it's fine

What I liked:

It's faster then my H2C even in single color prints, TPU is so much better, I had a lot of nozzle and extruder clogs on my H2C. It's my first real toolchanger and I like it so far!, I don't really care that the AMS 3H has only 2 drying spots it's enough for me. I will be trying out some nylon soon so wish me luck!

What I didn't like:

The printer is a bit to big but it's still manageable.

View In-Depth Breakdown

Comments (0)

P
PeterBEarned Spools November 9, 2026
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 10
Recommends this

10/10 and would buy again

Owned less than a month · Biggest problem: None (seriously - just works)

What I liked:

What I didn't like:

Comments (0)

Owner wall

Own one? Add yours

No verified owners yet. Post a photo of yours with your code and be the first on the wall.

Price history

Official US store, checked weekly

Price tracking for the H3C started Nov 3, 2026. The graph fills in as the weekly price checks come in.

Known issues 2

Report an issue

From brand advisories, owner forums and reviews, with sources on each. Newest first. Tap one for what happens and what fixes it.

  • Medium Clicking noise from the rear motors after the first day Last reported Nov 2026

    Within the first day or two of printing (about 8 to 38 hours), several H3C owners hear a clicking or ticking from the rear left motor area during prints and manual moves, and one also hears grinding on circular moves. Owners were on firmware 01.01.03.00. Bambu support asked for videos of diagonal moves to tell whether it comes from the motors or the idler pulleys; no cause has been confirmed yet.

    What fixes it: No confirmed fix. Open a support ticket with a video of the noise. An H2C owner with a similar noise traced it to an idler next to the motors with belt residue on it.

    From public reports: forum.bambulab.com · Confirm or add a fix

  • Medium H2C Build Plate Error on H3C Reported Nov 2026

    If you use any H2C's build plates you get a error that the H3C doesn't like that plate it says that it can bump into the toolchangers rack. You can disable this in the settings.

    Reported by MaxdepoesGames · Confirm or add a fix

On KeoPrints

More from KeoPrints

Not counted in any score.

Specs

Bambu Lab's nine-tool changer: nine docked, preheated PrintTools with their own filament paths, so material changes take about six seconds with very little purge. It comes with the AMS 3H, a sealed nine-slot filament box with a built-in dryer, prints TPU as soft as 75A, and has a 65 °C heated chamber, 350 °C hardened nozzles and a 330 × 320 × 325 mm build volume. The combo stands about a meter tall.

330 × 320 × 325 mmbuild volume
Enclosedformat
350 °Cmax nozzle
120 °Cmax bed
65 °C (active heating)chamber
1400 mm/s travel, 25,000 mm/s² accelerationmax speed
9 (SwapTek tool changer, nine PrintTools, about 6 s per switch)toolheads
November 2026released