Skip to content

Bambu Lab X2D

Owners like it. Good time to buy.

Bambu Lab X2D

9.4from 8 owners
8/25

Early read. Firms up at 25 owners.

$589 was $649
9% offLowest in 90 days
Buy at Bambu Lab

Price checked Nov 9 on the official US store.

Rate yours

Owner reviews 8 Rate it (10 seconds)

Reviewers earn Spools (site points) for any review, good or bad. Spools never change a score.

V
VirtuconEarned Spools November 9, 2026
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 10
Recommends this

10/10 and would buy again

Owned 1 to 6 months · Biggest problem: some issues with the track switch failing to feed

What I liked:

What I didn't like:

Comments (0)

O
owner-10061Earned Spools November 9, 2026
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 9
Recommends this

9/10 and would buy again

Owned 1 to 6 months · Biggest problem: aux nozzle clogs

What I liked:

What I didn't like:

Comments (0)

O
owner-82171Earned Spools November 9, 2026 (Edited)
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 9
Recommends this

9/10 and would buy again

Owned 1 to 6 months

What I liked:

What I didn't like:

Comments (0)

O
owner-67609Earned Spools November 9, 2026
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 9
Recommends this

9/10 and would buy again

Owned less than a month

What I liked:

What I didn't like:

Comments (0)

O
owner-18319Earned Spools November 9, 2026
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 9
Recommends this

9/10 and would buy again

Owned 6 to 12 months · Biggest problem: none

What I liked:

What I didn't like:

Comments (0)

Show all 8 owner reviews
O
owner-72000Earned Spools November 9, 2026
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 10
Recommends this

10/10 and would buy again

Owned 1 to 6 months · Biggest problem: AMS issues

What I liked:

What I didn't like:

Comments (0)

O
owner-10321Earned Spools November 9, 2026 (Edited)
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 10
Recommends this

10/10 and would buy again

Biggest problem: Hard to fix nozzle clogs

What I liked:

What I didn't like:

Comments (0)

O
owner-40334Earned Spools November 9, 2026 (Edited)
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 9
Recommends this

9/10 and would buy again

Owned 6 to 12 months · Biggest problem: AMS 2 Pro to X2D feeding errors. Thermister gets tangled up in the worn out nozzle boots when any kind of clogs happen, when you pull the plug, the thermister wire comes with it, and shuts down the printer.

What I liked:

What I didn't like:

Comments (0)

Owner wall

Own one? Add yours

No verified owners yet. Post a photo of yours with your code and be the first on the wall.

Price history

Official US store, checked weekly

Good time to buy. Now $589. At or near the lowest price we have tracked. Tracked since Apr 2026.

$589 now, $60 below the median ($649)
+$50−$50 $649 MayJunJulAugSepOctNov +$50−$50 $649 MayJulSepNov
Each week's price against the median price, lightly smoothed. Median $649, lowest $589 (week of Nov 16), highest $649, now $589 (−$60 vs median). 28 of 32 weeks are filled from launch announcements, brand sale emails or dated deal reports rather than our own store checks; hover a week to see which. Reported sales are assumed to last two weeks unless we know otherwise.
Weekly price
Week ofLowest pricevs medianSource
Apr 13, 2026$649$0launch price
Apr 20, 2026$649$0launch price
Apr 27, 2026$649$0launch price
May 4, 2026$649$0launch price
May 11, 2026$649$0launch price
May 18, 2026$649$0launch price
May 25, 2026$649$0launch price
Jun 1, 2026$649$0launch price
Jun 8, 2026$649$0launch price
Jun 15, 2026$649$0launch price
Jun 22, 2026$649$0launch price
Jun 29, 2026$649$0launch price
Jul 6, 2026$649$0launch price
Jul 13, 2026$649$0launch price
Jul 20, 2026$649$0launch price
Jul 27, 2026$649$0launch price
Aug 3, 2026$649$0launch price
Aug 10, 2026$649$0launch price
Aug 17, 2026$649$0launch price
Aug 24, 2026$649$0launch price
Aug 31, 2026$649$0launch price
Sep 7, 2026$649$0launch price
Sep 14, 2026$649$0launch price
Sep 21, 2026$649$0launch price
Sep 28, 2026$649$0launch price
Oct 5, 2026$649$0launch price
Oct 12, 2026$649$0launch price
Oct 19, 2026$649$0launch price
Oct 26, 2026$589−$60store check
Nov 2, 2026$589−$60store check
Nov 9, 2026$589−$60store check
Nov 16, 2026$589−$60store check

Known issues 4

Report an issue

From brand advisories, owner forums and reviews, with sources on each. Newest first. Tap one for what happens and what fixes it.

  • Medium Printer drops off Wi-Fi or loses its network connection Last reported Oct 2026

    Owners report the X2D losing its connection before, during or after prints, failing to reconnect, or showing no networks at all, often needing a power cycle. About 6 owners in one thread, May to June 2026; one was on firmware 01.01.00.00.

    What fixes it: Workarounds owners report include a separate 2.4 GHz network name, turning off band steering on the router, or adding an access point near the printer; problems returned for some. Bambu agreed to ship a replacement antenna to one owner after reviewing logs, and one owner saw improvement after a later firmware update.

    From public reports: forum.bambulab.com · Confirm or add a fix

  • Medium Under-extrusion and gaps on top surfaces and walls Last reported Oct 2026

    Several owners see uneven walls, visible gaps and under-extruded top layers, which flow and pressure advance calibration did not cure. Some compare the same files on an A1 Mini or P1S and get cleaner results. Reports started in May 2026 and continued into July.

    What fixes it: No confirmed fix. One owner suggested raising the flow ratio above 1.0, but another still saw a crisscross top layer at 1.05. Some owners are waiting on a firmware update.

    From public reports: forum.bambulab.com, forum.bambulab.com · Confirm or add a fix

  • Medium AMS 2 Pro filament fails to load or feed, often from slot 1 Last reported Oct 2026

    Owners of new X2D Combos report filament that reaches the toolhead but is not gripped by the left extruder, load errors, AMS assist motor overload, and a slot 1 that will not feed unless pushed by hand. Retries loop and multicolor prints fail. Roughly a dozen owners across two threads, starting the week the printer shipped.

    What fixes it: Two owners report fixing it by rerouting the PTFE tubes with gentler bends (swapping the auxiliary and main tube positions and moving a clip). Others point to a hub shimming fix from an AMS 2 Pro thread, not confirmed on the X2D. Owners report Bambu agreeing to send a replacement AMS internal hub in at least one warranty case.

    From public reports: forum.bambulab.com, forum.bambulab.com · Confirm or add a fix

  • Low False Filament Track Switch mismatch warning Last reported Sep 2026

    When sending a job from Bambu Studio, many owners get a warning that the installed Filament Track Switch does not match the sliced file, including owners who never installed the accessory. Re-slicing does not reliably clear it. Owners report prints continue normally, but it can show on almost every print and Bambu has not explained it.

    What fixes it: Owners mostly ignore it. Running AMS auto-detection on the printer and then syncing and re-slicing in Studio clears it for one owner some of the time; results are mixed.

    From public reports: forum.bambulab.com, forum.bambulab.com · Confirm or add a fix

On The 3D Print Stop

More from The 3D Print Stop

From The 3D Print Stop, the Bellevue, Nebraska print shop Keo works with. Their own machines, used every day.

Not counted in any score.

Specs

The X2D is Bambu Lab's replacement for the X1 series: an enclosed dual-nozzle printer with a heated chamber and a 256 mm class build area. It suits people who want two-material or support-material printing and engineering filaments in a P2S-sized footprint without paying H2D prices.

256 × 256 × 260 mmbuild volume
CoreXY, enclosedformat
300 °Cmax nozzle
120 °Cmax bed
65 °C (active heating)chamber
1000 mm/smax speed
2 (dual nozzle)toolheads
April 2026released
What the press said · 9.0 from 2 press outlets · Read them

What reviewers say 9.0 from 2

How scores work
  • 9.0 Tom's HardwareAn Editor's Choice rebuild of the X1 line that brings a second nozzle, heated chamber and better filtration … 4.5/5 · Apr 2026

    An Editor's Choice rebuild of the X1 line that brings a second nozzle, heated chamber and better filtration close to H2 level, with the Bowden-fed second nozzle as the main weak spot.

    • Dual nozzle cuts purge waste on two-color prints
    • Active chamber heating
    • Quick-swap nozzles
    • Auxiliary nozzle is Bowden fed and slower
    • Struggles with soft TPU on second nozzle
    • No USB stick included

    Read the full review on Tom's Hardware · by Denise Bertacchi

  • 9.0 TechRadarA true professional engineering machine and a strong X1C successor that ran 250 hours without a failure, though … 4.5/5 · Apr 2026

    A true professional engineering machine and a strong X1C successor that ran 250 hours without a failure, though the Bowden second hotend is slower and nozzle assignment is confusing.

    • Dual-nozzle system
    • Hardened nozzles ready for abrasives
    • Zero failures in long testing
    • Bowden hotend speed is limited
    • Filament assignment confusing in Bambu Studio
    • No filament recycling option

    Read the full review on TechRadar · by Alastair Jennings