Skip to content

Elegoo Neptune 4 Plus

No owners yet. Here's everything else.

Elegoo Neptune 4 Plus

0 of 5 owners · 5 more and the score goes live.

Own one? Tap your score:
$309 was $425
27% off
Buy at Elegoo

Paid link. We may earn a commission at no extra cost to you. How this works

Price checked Nov 7 on the official US store.

Owner reviews 0 Rate it (10 seconds)

Reviewers earn Spools (site points) for any review, good or bad. Spools never change a score.

No owner reviews yet. If you own a Neptune 4 Plus, yours will be the first, and it starts this printer's ranking.

Owner wall

Own one? Add yours

No verified owners yet. Post a photo of yours with your code and be the first on the wall.

Price history

Official US store, checked weekly

Normal price. Now $309. About its usual $297. Tracked since Nov 2025.

$309 now, $20 above the median ($289)
$289 +$30 DecJan 26FebMarAprMayJunJulAugSepOctNov $289 +$30 Jan 26MarMayJulSepNov
Each week's price against the median price, lightly smoothed. Median $289, lowest $269 (week of Oct 12), highest $319, now $309 (+$20 vs median). 1 of 53 weeks are filled from launch announcements, brand sale emails or dated deal reports rather than our own store checks; hover a week to see which. Reported sales are assumed to last two weeks unless we know otherwise.
Weekly price
Week ofLowest pricevs medianSource
Nov 17, 2025$269.99−$19store check
Nov 24, 2025$269.99−$19store check
Dec 1, 2025$269−$20store check
Dec 8, 2025$269−$20store check
Dec 15, 2025$269−$20store check
Dec 22, 2025$269−$20store check
Dec 29, 2025$269−$20store check
Jan 5, 2026$319+$30store check
Jan 12, 2026$319+$30store check
Jan 19, 2026$319+$30store check
Jan 26, 2026$309+$20store check
Feb 2, 2026$289$0store check
Feb 9, 2026$289$0estimated end of a sale
Feb 16, 2026$279−$10store check
Feb 23, 2026$279−$10store check
Mar 2, 2026$279−$10store check
Mar 9, 2026$279−$10store check
Mar 16, 2026$279−$10store check
Mar 23, 2026$279−$10store check
Mar 30, 2026$279−$10store check
Apr 6, 2026$279−$10store check
Apr 13, 2026$309+$20store check
Apr 20, 2026$309+$20store check
Apr 27, 2026$309+$20store check
May 4, 2026$289$0store check
May 11, 2026$289$0store check
May 18, 2026$289$0store check
May 25, 2026$289$0store check
Jun 1, 2026$289$0store check
Jun 8, 2026$309+$20store check
Jun 15, 2026$309+$20store check
Jun 22, 2026$309+$20store check
Jun 29, 2026$309+$20store check
Jul 6, 2026$309+$20store check
Jul 13, 2026$309+$20store check
Jul 20, 2026$309+$20store check
Jul 27, 2026$309+$20store check
Aug 3, 2026$309+$20store check
Aug 10, 2026$309+$20store check
Aug 17, 2026$269−$20store check
Aug 24, 2026$269−$20store check
Aug 31, 2026$269−$20store check
Sep 7, 2026$269−$20store check
Sep 14, 2026$309+$20store check
Sep 21, 2026$269−$20store check
Sep 28, 2026$269−$20store check
Oct 5, 2026$269−$20store check
Oct 12, 2026$269−$20store check
Oct 19, 2026$279−$10store check
Oct 26, 2026$279−$10store check
Nov 2, 2026$309+$20store check
Nov 9, 2026$309+$20store check
Nov 16, 2026$309+$20store check

Known issues 6, 1 serious

Report an issue

From brand advisories, owner forums and reviews, with sources on each. Newest first. Tap one for what happens and what fixes it.

  • High Klipper updates from Fluidd break the stock firmware Last reported Oct 2026

    Like the rest of the Neptune 4 line, the Neptune 4 Plus runs a modified Klipper that cannot be updated from upstream, and owners who use the Fluidd update buttons can end up with a printer that will not start. Elegoo's wiki tells owners not to update through Fluidd.

    What fixes it: Update only with Elegoo's USB packages. Recover a broken unit by reflashing the eMMC image for the correct model and revision.

    From public reports: tomshardware.com, klipper.discourse.group, printer-hub.com · Confirm or add a fix

  • Medium Z offset not saved reliably or drifts Last reported Oct 2026

    Reviewers and owners report that the Neptune 4 Plus does not always keep the saved nozzle-to-bed distance, so first layers change between prints. Tom's Hardware had to set the Z height through Klipper's web interface by hand on the 4 Max. Probe thermal drift, over-tight wheels or Z nut screws, and bed springs that sag over time add to it.

    What fixes it: Calibrate Z offset with the bed heat-soaked (about 20 minutes at 60 °C), set it only from the printer's screen, check the eccentric wheels and Z nut screws are not over-tightened, and confirm the mesh profile loads in the start G-code.

    From public reports: wiki.elegoo.com, tomshardware.com, printer-hub.com · Confirm or add a fix

  • Medium Heated bed fails to reach temperature Last reported Oct 2026

    Some Neptune 4 Plus units abort prints with a 'heater_bed not heating at expected rate' error. Elegoo has a troubleshooting page for heated bed heating failure on the ribbon-cable 4 Plus and 4 Max, and the causes it lists include a room below 25 °C and the rear auxiliary fan running before the bed reaches temperature. A wrong setting on the 115/230 V selector can also stop the bed heating.

    What fixes it: Keep the rear fan off until the bed is at temperature, use an enclosure in a cold room, check the recessed 115/230 V selector with the printer unplugged, and inspect the fuse, bed harness, thermistor connector and heater terminals.

    From public reports: wiki.elegoo.com, printer-hub.com · Confirm or add a fix

  • Medium Large heated bed wobbles on its wheels Last reported Oct 2026

    Owners find play in the Neptune 4 Plus bed carriage, which shows up as layer artifacts and inconsistent first layers. Elegoo attributes it to unadjusted eccentric wheels, Y extrusions that are not parallel, or a deformed slider plate, and has an official wiki page on it.

    What fixes it: Adjust the eccentric nuts until the bed has no rock but still rolls freely. If more than two wheels stay loose, check the Y rails for parallelism or ask Elegoo for a replacement slider plate.

    From public reports: wiki.elegoo.com, printer-hub.com · Confirm or add a fix

  • Medium Sensorless homing slams or grinds against the frame Last reported Oct 2026

    The Neptune 4 Plus has no physical X/Y endstops, and units can keep driving into the frame during homing with a loud grinding sound. Tom's Hardware heard the 4 Max ram its stops on early firmware and said Elegoo updates mostly sorted it out. Printer Hub's roundup points to belt tension as the usual cause, and Elegoo has a wiki page for motors that keep crushing while homing.

    What fixes it: Update to current Elegoo firmware, set belt tension per Elegoo's guide, and follow Elegoo's troubleshooting page for motors that keep crushing while homing.

    From public reports: wiki.elegoo.com, tomshardware.com, printer-hub.com · Confirm or add a fix

  • Medium Firmware mismatch leaves screen stuck or model misidentified Last reported Oct 2026

    On the Neptune 4 Plus, the mainboard and screen firmware must be a matched pair for the right hardware revision, and the fix pack for one revision can brick the other. Symptoms include the screen stuck on the loading screen, a blank mainboard firmware version, or the printer reporting itself as a different Neptune 4 model. Elegoo has an official wiki page for the stuck loading screen on the 4 Plus and 4 Max.

    What fixes it: Identify the revision first, then flash the matching fix pack, mainboard and screen firmware from Elegoo. If the printer reports the wrong model after flashing an eMMC image, Elegoo support has supplied model-specific update files.

    From public reports: wiki.elegoo.com, github.com, printer-hub.com · Confirm or add a fix

Specs

A larger Neptune 4 with a 320 × 320 × 385 mm volume, Klipper firmware and a 500 mm/s rated speed. It suits people who want a roomy, low-cost bed slinger for bigger single-color parts.

320 × 320 × 385 mmbuild volume
Bed slinger, open frameformat
300 °Cmax nozzle
None (open frame)chamber
500 mm/smax speed
1toolheads
September 2023released

Consider instead

What the press said · 9.0 from 1 press outlet · Read them

What reviewers say 9.0 from 1

How scores work
  • 9.0 Tom's HardwareA big-bed Klipper machine that adds speed and Wi-Fi over the Neptune 3 Plus and outperforms most printers … 4.5/5 · Dec 2023

    A big-bed Klipper machine that adds speed and Wi-Fi over the Neptune 3 Plus and outperforms most printers in its price range. Editor's Choice pick.

    • 400W PSU for fast heating
    • Built-in Wi-Fi and Klipper
    • Strong part cooling and dual-gear extruder
    • Custom nozzle sizes not yet available
    • Semi-automatic bed leveling trails rivals

    Read the full review on Tom's Hardware · by Andrew Sink