Skip to content

Elegoo Neptune 4

No owners yet. Here's everything else. Wait for a sale.

Elegoo Neptune 4

0 of 5 owners · 5 more and the score goes live.

Own one? Tap your score:
$219 was $249 Sold out
12% off
Buy at Elegoo

Paid link. We may earn a commission at no extra cost to you. How this works

Price checked Nov 7 on the official US store.

Owner reviews 0 Rate it (10 seconds)

Reviewers earn Spools (site points) for any review, good or bad. Spools never change a score.

No owner reviews yet. If you own a Neptune 4, yours will be the first, and it starts this printer's ranking.

Owner wall

Own one? Add yours

No verified owners yet. Post a photo of yours with your code and be the first on the wall.

Price history

Official US store, checked weekly

Wait for a sale. Now $219. Above its usual $207. It has been as low as $159. Tracked since Dec 2025.

$219 now, $14 above the median ($205)
+$50−$50 $205 +$45 DecJan 26FebMarAprMayJunJulAugSepOctNov +$50−$50 $205 +$45 Jan 26MarMayJulSepNov
Each week's price against the median price, lightly smoothed. Median $205, lowest $159 (week of Dec 22), highest $250, now $219 (+$14 vs median). 2 of 53 weeks are filled from launch announcements, brand sale emails or dated deal reports rather than our own store checks; hover a week to see which. Reported sales are assumed to last two weeks unless we know otherwise.
Weekly price
Week ofLowest pricevs medianSource
Nov 17, 2025$250+$45estimated end of a sale
Nov 24, 2025$250+$45estimated end of a sale
Dec 1, 2025$159−$46store check
Dec 8, 2025$159−$46store check
Dec 15, 2025$159−$46store check
Dec 22, 2025$159−$46store check
Dec 29, 2025$199−$6store check
Jan 5, 2026$199−$6store check
Jan 12, 2026$199−$6store check
Jan 19, 2026$199−$6store check
Jan 26, 2026$199−$6store check
Feb 2, 2026$199−$6store check
Feb 9, 2026$219+$14store check
Feb 16, 2026$219+$14store check
Feb 23, 2026$225+$20store check
Mar 2, 2026$225+$20store check
Mar 9, 2026$225+$20store check
Mar 16, 2026$225+$20store check
Mar 23, 2026$225+$20store check
Mar 30, 2026$225+$20store check
Apr 6, 2026$219+$14store check
Apr 13, 2026$219+$14store check
Apr 20, 2026$219+$14store check
Apr 27, 2026$205$0store check
May 4, 2026$205$0store check
May 11, 2026$205$0store check
May 18, 2026$205$0store check
May 25, 2026$205$0store check
Jun 1, 2026$205$0store check
Jun 8, 2026$205$0store check
Jun 15, 2026$205$0store check
Jun 22, 2026$204−$1store check
Jun 29, 2026$204−$1store check
Jul 6, 2026$204−$1store check
Jul 13, 2026$204−$1store check
Jul 20, 2026$204−$1store check
Jul 27, 2026$204−$1store check
Aug 3, 2026$204−$1store check
Aug 10, 2026$204−$1store check
Aug 17, 2026$204−$1store check
Aug 24, 2026$209+$4store check
Aug 31, 2026$209+$4store check
Sep 7, 2026$209+$4store check
Sep 14, 2026$204−$1store check
Sep 21, 2026$204−$1store check
Sep 28, 2026$204−$1store check
Oct 5, 2026$204−$1store check
Oct 12, 2026$204−$1store check
Oct 19, 2026$204−$1store check
Oct 26, 2026$204−$1store check
Nov 2, 2026$219+$14store check
Nov 9, 2026$219+$14store check
Nov 16, 2026$219+$14store check

Known issues 5, 1 serious

Report an issue

From brand advisories, owner forums and reviews, with sources on each. Newest first. Tap one for what happens and what fixes it.

  • High Klipper updates from Fluidd or Mainsail break the printer Last reported Oct 2026

    Elegoo ships a modified Klipper build, and using the update buttons in Fluidd or Mainsail (for example after adding webcam or timelapse settings) can leave the Neptune 4 unable to start Klipper, with errors such as 'CommandWrapper has no attribute get_command_tag'. Two owners reported this exact error on the Klipper forum in September 2023, and one got the printer working again only after Elegoo sent a replacement eMMC module. A Klipper forum regular said the official Klipper project cannot support Elegoo's fork, and Elegoo's own instructions say updating to official Klipper, Moonraker or Fluidd is not supported.

    What fixes it: Only update with Elegoo's official USB firmware packages. If the system is already broken, reapply the fix pack and firmware in order, reflash the eMMC image, or ask Elegoo support about a replacement eMMC.

    From public reports: klipper.discourse.group, printer-hub.com, tomshardware.com · Confirm or add a fix

  • Medium Heat creep clogs on long or hot prints Last reported Oct 2026

    The Neptune 4 feeds filament through a PTFE tube into the heat break, and Printer Hub collects owner reports of heat creep clogs late in long prints, often 70 to 90 percent of the way through. A stalled heat-break fan, back-to-back prints and sustained printing above about 250 °C make it worse. The nozzle is also a custom Elegoo design, so standard replacement nozzles do not fit. Elegoo has a nozzle clogging page for the Neptune series.

    What fixes it: Confirm the heat-break fan spins whenever the nozzle is hot, let the heat break cool between back-to-back prints, reseat or replace the PTFE tube, re-torque the nozzle hot, and use only nozzles made for the Neptune 4 and 4 Pro. For sustained printing above about 250 °C, Printer Hub suggests an all-metal hotend.

    From public reports: wiki.elegoo.com, printer-hub.com · Confirm or add a fix

  • Medium Blob of death and filament leaking around the hotend Last reported Oct 2026

    When a part detaches mid-print, plastic can build up around the Neptune 4 hotend and encase the heater block and wiring. The thermistor leads are very thin and can snap when the blob is pulled off, after which the printer shows a below-zero temperature and will not heat. Elegoo has a wiki page on this for the Neptune 4 and 4 Pro, and Printer Hub reports Elegoo does not treat it as a warranty case.

    What fixes it: Check the cold temperature reading first. Heat to about 200 °C, power off, and pull the blob off while warm without pulling on wires; replace the thermistor if it reads below zero. Re-torque the nozzle hot, then re-level and reset the Z offset. Prevent it with a correct Z offset, a clean plate and supports on small-footprint models.

    From public reports: wiki.elegoo.com, printer-hub.com · Confirm or add a fix

  • Medium Z offset drifts or does not stick between prints Last reported Oct 2026

    Owners report the first layer changing from one print to the next on the Neptune 4, with the saved Z offset not being applied or shifting by a few tenths of a millimeter. Causes cited include inductive probe drift as the bed heats, mechanical play in the wheels and gantry, and the saved bed mesh not being loaded by the default start G-code. Elegoo has a wiki page titled Abnormal Z Offset for the Neptune 4 and 4 Pro.

    What fixes it: Calibrate the probe with the bed and nozzle at printing temperature, level from only one place (touchscreen or web UI), and add a bed mesh load command to the slicer start G-code. Check wheel preload and gantry squareness.

    From public reports: wiki.elegoo.com, printer-hub.com, tomshardware.com · Confirm or add a fix

  • Medium Wrong firmware for ribbon vs Type-C hardware revision Last reported Oct 2026

    The Neptune 4 was built in two hardware revisions (ribbon printhead cable and Type-C cable) that need different firmware and printhead parts. Flashing the package for the other revision, or applying files in the wrong order, can leave the screen stuck on the logo or the printer unable to boot.

    What fixes it: Identify the revision by the printhead cable, download from the matching column on Elegoo's download page, and apply the fix pack, mainboard firmware and screen firmware in Elegoo's stated order using a FAT32 USB 2.0 drive.

    From public reports: elegoo.com, printer-hub.com · Confirm or add a fix

Specs

A compact Klipper-based bed slinger with a 225 mm bed, direct drive extruder and 500 mm/s rated speed. It suits first-time buyers who want a cheap, tinkerer-friendly printer and do not need multicolor.

225 × 225 × 265 mmbuild volume
Bed slinger, open frameformat
300 °Cmax nozzle
110 °Cmax bed
None (open frame)chamber
500 mm/smax speed
1toolheads
June 2023released

Consider instead

What the press said · 7.0 from 1 press outlet · Read them

What reviewers say 7.0 from 1

How scores work
  • 7.0 Tom's HardwareEssentially the sturdy Neptune 3 Pro with Klipper speed added, but without built-in WiFi or a Klipper screen … 3.5/5 · Aug 2023

    Essentially the sturdy Neptune 3 Pro with Klipper speed added, but without built-in WiFi or a Klipper screen the firmware's extras are hard to reach.

    • Easy to use
    • Klipper precision
    • Direct drive dual gear extruder
    • Klipper features are hidden
    • No WiFi included
    • Frustrating bed leveling

    Read the full review on Tom's Hardware · by Denise Bertacchi

  • n/a Tech AdvisorCovers what most people want in a first 3D printer, as long as you avoid Elegoo's buggy slicer. Oct 2023

    Covers what most people want in a first 3D printer, as long as you avoid Elegoo's buggy slicer.

    • Relatively fast
    • Automatic bed leveling
    • Beginner friendly touchscreen
    • No WiFi
    • Unreliable Elegoo slicer

    Read the full review on Tech Advisor · by Anyron Copeman