Skip to content

Creality Ender-3 V3 SE

Not enough owners for a score yet. Here's what they say so far.

Creality Ender-3 V3 SE

1 of 5 owners · 4 more and the score goes live.

Own one? Tap your score:
$199
Buy at Creality

Paid link. We may earn a commission at no extra cost to you. How this works

Price checked Nov 9 on the official US store.

Owner reviews 1 Rate it (10 seconds)

Reviewers earn Spools (site points) for any review, good or bad. Spools never change a score.

Not enough owner reviews for an overall owner rating yet: 1 of 5. Every rating is shown below as it comes in. Own one? Add yours.

O
owner-67609Earned Spools November 9, 2026
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 7
Does not recommend

7/10, would not buy again

Owned over 2 years · Biggest problem: no wifi, slow.

What I liked:

What I didn't like:

Comments (0)

Owner wall

Own one? Add yours

No verified owners yet. Post a photo of yours with your code and be the first on the wall.

Price history

Official US store, checked weekly

Normal price. Now $199. About its usual $194. Tracked since Nov 2025.

$199 now, right at the median ($199)
$199 DecJan 26FebMarAprMayJunJulAugSepOctNov $199 Jan 26MarMayJulSepNov
Each week's price against the median price, lightly smoothed. Median $199, lowest $179 (week of Nov 2), highest $199, now $199 ($0 vs median).
Weekly price
Week ofLowest pricevs medianSource
Nov 17, 2025$179.99−$19store check
Nov 24, 2025$179.99−$19store check
Dec 1, 2025$179.99−$19store check
Dec 8, 2025$179.99−$19store check
Dec 15, 2025$179.99−$19store check
Dec 22, 2025$179.99−$19store check
Dec 29, 2025$179.99−$19store check
Jan 5, 2026$179−$20store check
Jan 12, 2026$179−$20store check
Jan 19, 2026$179−$20store check
Jan 26, 2026$179−$20store check
Feb 2, 2026$179−$20store check
Feb 9, 2026$179−$20store check
Feb 16, 2026$199$0store check
Feb 23, 2026$199$0store check
Mar 2, 2026$199$0store check
Mar 9, 2026$199$0store check
Mar 16, 2026$199$0store check
Mar 23, 2026$199$0store check
Mar 30, 2026$199$0store check
Apr 6, 2026$199$0store check
Apr 13, 2026$199$0store check
Apr 20, 2026$199$0store check
Apr 27, 2026$199$0store check
May 4, 2026$199$0store check
May 11, 2026$199$0store check
May 18, 2026$199$0store check
May 25, 2026$199$0store check
Jun 1, 2026$199$0store check
Jun 8, 2026$199$0store check
Jun 15, 2026$199$0store check
Jun 22, 2026$199$0store check
Jun 29, 2026$199$0store check
Jul 6, 2026$199$0store check
Jul 13, 2026$199$0store check
Jul 20, 2026$199$0store check
Jul 27, 2026$199$0store check
Aug 3, 2026$199$0store check
Aug 10, 2026$199$0store check
Aug 17, 2026$199$0store check
Aug 24, 2026$199$0store check
Aug 31, 2026$199$0store check
Sep 7, 2026$199$0store check
Sep 14, 2026$199$0store check
Sep 21, 2026$199$0store check
Sep 28, 2026$199$0store check
Oct 5, 2026$199$0store check
Oct 12, 2026$179−$20store check
Oct 19, 2026$179−$20store check
Oct 26, 2026$179−$20store check
Nov 2, 2026$179−$20store check
Nov 9, 2026$199$0store check
Nov 16, 2026$199$0store check

Known issues 1, 1 serious

Report an issue

From brand advisories, owner forums and reviews, with sources on each. Newest first. Tap one for what happens and what fixes it.

  • High CR Touch errors and nozzle crashing into the bed while leveling Last reported Oct 2026

    Owners report CR Touch sensor errors at boot or during auto-leveling, sometimes with a long beep or boot loop, and in other cases the nozzle keeps pushing down into the bed during leveling, which can dent or burn the bed surface. It has been reported on new units out of the box and on printers a few months old. Three threads on Creality's forum cover roughly 20 to 24 owners.

    What fixes it: Owners often clear it by freeing a sticking probe pin, and two fixed a binding plunger with a small shim or spacer. Others fixed it by cleaning debris from under the bed or moving bed wiring that touched the heater; one owner suspects the hotend cover pinches the CR Touch cable. When that fails, Creality support has sent replacement CR Touch probes or strain gauges under warranty. Results are mixed and several threads end unresolved.

    From public reports: forum.creality.com, forum.creality.com, forum.creality.com · Confirm or add a fix

Older or fixed issues (2)
  • Medium Gritty or loose Y-axis rods cause grinding and uneven prints Last reported Oct 2025

    The dual Y-axis rods can feel gritty or have play where they sit in the front supports, giving a grinding noise as the bed moves or print defects away from the bed center. Owners traced it to a damaged rod or bearing, or to front set screws that are too short to clamp the rod.

    What fixes it: Owners have rotated the bad rod, used slightly longer M3x5 grub screws or a small shim to take up play, or fitted a linear rail kit. Some asked Creality support for replacement rods under warranty, but no outcome was posted.

    From public reports: forum.creality.com, forum.creality.com · Confirm or add a fix

  • Medium Extrusion stops mid-print with clicking or thin lines Last reported Dec 2024

    Prints start fine, then the extruder clicks or the line thins out and extrusion stops while the printer keeps moving, with no error shown. One owner hit it within two weeks and two spools of PLA, and swapping filament or the nozzle did not cure it for the owners who tried.

    What fixes it: A forum regular suggested backing off the extruder tension screw in quarter turns, which gave mixed results. Also check that the hotend fan spins (a dead fan causes heat creep) and keep slicer retraction short (about 0.8 to 1.2 mm). Neither thread reached a confirmed fix.

    From public reports: forum.creality.com, forum.creality.com · Confirm or add a fix

Specs

Creality's cheapest current Ender, a classic bed slinger with auto leveling and a direct-drive extruder. Suits first-time buyers and kids or students on a tight budget who mostly print PLA.

220 × 220 × 250 mmbuild volume
Bed slinger, open frameformat
260 °Cmax nozzle
100 °Cmax bed
None (open frame)chamber
250 mm/smax speed
1toolheads
August 2023released
What the press said · 9.0 from 2 press outlets · Read them

What reviewers say 9.0 from 2

How scores work
  • 9.0 TechRadarAn affordable, reliable entry-level printer that makes a great first machine for beginners. 4.5/5 · Dec 2023

    An affordable, reliable entry-level printer that makes a great first machine for beginners.

    • Low price
    • Reliable performance
    • Beginner friendly
    • No touchscreen
    • No filament runout sensor
    • No camera

    Read the full review on TechRadar · by Alastair Jennings

  • 9.0 Tom's HardwareA beginner's dream that brings formerly premium features to a sub-$200 printer, though it is not a speed … 4.5/5 · Sep 2023

    A beginner's dream that brings formerly premium features to a sub-$200 printer, though it is not a speed leader like the K1.

    • Very affordable
    • Easy assembly
    • Excellent auto bed leveling
    • Sticky PC build plate is hard to clean

    Read the full review on Tom's Hardware · by Denise Bertacchi