Skip to content

Elegoo Centauri Carbon 2

Not enough owners for a score yet. Here's what they say so far.

Elegoo Centauri Carbon 2

2 of 5 owners · 3 more and the score goes live.

Own one? Tap your score:
$349 was $359
3% off
Buy at Elegoo

Paid link. We may earn a commission at no extra cost to you. How this works

Price checked Nov 7 on the official US store.

Owner reviews 2 Rate it (10 seconds)

Reviewers earn Spools (site points) for any review, good or bad. Spools never change a score.

Not enough owner reviews for an overall owner rating yet: 2 of 5. Every rating is shown below as it comes in. Own one? Add yours.

O
owner-54587Earned Spools November 9, 2026
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 8
Recommends this

8/10 and would buy again

Owned 6 to 12 months · Biggest problem: app and slicer connection issues

What I liked:

What I didn't like:

Comments (0)

B
BrendanEarned Spools November 9, 2026 (Edited)
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 9
Recommends this

9/10 and would buy again

Owned 1 to 6 months · Biggest problem: This printer does not appear to be accessible via a standard web page. One has to view either in an app or in Orca. Not an app guy. Would prefer if you can just point a browser at it and see your printing progress.

What I liked:

I am an owner of the CC1 as well, and since this printer is more or less an evolution of the CC1 platform, most of my positive review of that printer applies here. I love the Price/Value ratio, 350 degree nozzle temp, 100 degree bed temp, plus hardened nozzle out of the box. I also like the revised bed leveling; if you print an object, it levels the bed just around the area you are actually going to print on instead of the whole bed. Saves a lot of time and makes including leveling on each print doable. I use stock Orca which it works fine with on LAN only mode. If one is considering the single-color version of this printer, I can think of no better value than this one for printing engineering parts.

What I didn't like:

I don't like the fact that you can no longer just browse to the printer via web browser and view printing progress like you could with the CC1. Not an app guy, so maybe this isn't a factor for most. I am also not sure if this was just my experience, but evidently combo kits essentially send you a non-combo printer and an AMS conversion kit, necessitating some removal of single color parts during initial setup. Though I can see the flexibility this would provide a manufacturer, it means that the user must be more involved in the assembly than I feel they should have to be. Initial CC2 kits seemed to require less assembly/disassembly to complete an AMS model. The lack of a chamber heater is a minus, so If you want to print the Highest temp stuff an additional chamber heater solution may be necessary. There are currently no chamber heaters from Elegoo or third parties that integrate with the printer. I am working on that }:0)

Comments (0)

Owner wall

Own one? Add yours

No verified owners yet. Post a photo of yours with your code and be the first on the wall.

Price history

Official US store, checked weekly

Normal price. Now $349. About its usual $340. Tracked since Jun 2026.

$349 now, $10 above the median ($339)
$339 +$10 JulAugSepOctNov $339 +$10 JulSepNov
Each week's price against the median price, lightly smoothed. Median $339, lowest $329 (week of Sep 7), highest $349, now $349 (+$10 vs median).
Weekly price
Week ofLowest pricevs medianSource
Jun 22, 2026$339$0store check
Jun 29, 2026$339$0store check
Jul 6, 2026$339$0store check
Jul 13, 2026$339$0store check
Jul 20, 2026$339$0store check
Jul 27, 2026$339$0store check
Aug 3, 2026$339$0store check
Aug 10, 2026$339$0store check
Aug 17, 2026$329−$10store check
Aug 24, 2026$329−$10store check
Aug 31, 2026$329−$10store check
Sep 7, 2026$329−$10store check
Sep 14, 2026$339$0store check
Sep 21, 2026$339$0store check
Sep 28, 2026$339$0store check
Oct 5, 2026$339$0store check
Oct 12, 2026$339$0store check
Oct 19, 2026$349+$10store check
Oct 26, 2026$349+$10store check
Nov 2, 2026$349+$10store check
Nov 9, 2026$349+$10store check
Nov 16, 2026$349+$10store check

Known issues 2

Report an issue

From brand advisories, owner forums and reviews, with sources on each. Newest first. Tap one for what happens and what fixes it.

  • Medium Nozzle clogs are hard to clear because of the CANVAS hub Last reported Feb 2026

    The CANVAS hub collets grip the PTFE tubes so tightly they could not be removed, so clearing an extruder clog means unscrewing the whole hub. The loading routine also does not get hot enough to clear leftover high-temperature filament from the nozzle. Elegoo documents CANVAS feed fault codes 1242, 1243 and 1263, which a reseller guide links to spool drag, poor PTFE seating, wet or oversized filament and partial clogs.

    What fixes it: Per the reseller guide: test with one dry known-good spool on one channel, cut a clean tip and reseat PTFE tubes. Clearing an extruder clog itself means removing the hub.

    From public reports: tomshardware.com, openelab.io · Confirm or add a fix

  • Low Side spool holders slip or break with some spools Last reported Feb 2026

    The side-mounted spool holders are sized for Elegoo spools and do not work well with some other brands: one reviewer had a reel slip off, and another broke a holder when a third-party cardboard spool got stuck. The mounts also push spools outward and widen the footprint.

    What fixes it: One reviewer stopped slipping by adding a small rubber sticker to the holder.

    From public reports: tomshardware.com, techradar.com · Confirm or add a fix

Specs

An enclosed CoreXY printer with a die-cast aluminum frame, a 256 mm cube build volume, a 350 °C hardened steel hotend and a 110 °C bed. It is aimed at hobbyists printing PLA through filled engineering filaments, with 4-color printing available through the CANVAS hub included in the Combo.

256 × 256 × 256 mmbuild volume
CoreXY, enclosedformat
350 °Cmax nozzle
110 °Cmax bed
Passive (enclosed, no heater)chamber
500 mm/smax speed
1 (4-color with CANVAS combo)toolheads
Centauri Carbon Centauri Carbon 2replaces
January 2026released

Consider instead

What the press said · 8.5 from 2 press outlets · Read them

What reviewers say 8.5 from 2

How scores work
  • 9.0 TechRadarOne of the cheapest and most dependable multi-filament machines around, with an enclosed chamber and integrated four-color system. 4.5/5 · Jan 2026

    One of the cheapest and most dependable multi-filament machines around, with an enclosed chamber and integrated four-color system.

    • Integrated CANVAS multicolor system
    • Fully enclosed
    • High nozzle temperature
    • Limited to four filaments
    • Spools sit outside the printer
    • Purge waste

    Read the full review on TechRadar · by Alastair Jennings

  • 8.0 Tom's HardwareA pleasant budget CoreXY with a clunky-looking but reliable four-color add-on; it is a new machine rather than … 4/5 · Feb 2026

    A pleasant budget CoreXY with a clunky-looking but reliable four-color add-on; it is a new machine rather than an upgrade for original Centauri owners.

    • Handles TPU well in the CANVAS system
    • Fully enclosed
    • No cloud account required
    • No heated chamber
    • Spool holders fit many brands poorly
    • Cold plate adhesion is weak

    Read the full review on Tom's Hardware · by Denise Bertacchi

KeoPrints review

Not counted in the Internet score

Keo's take

Keo spent this sponsored video trying to make the Centauri Carbon 2 fail with hard ASA and composite prints, and it struggled at the extremes. For normal engineering and abrasive printing, though, he says it does pretty well and offers a lot of versatility, usability and reliability for an excellent price.

Pros, cons and the video
  • Generic PA12-CF profile printed clean, barely warped parts
  • Build plate holds warp-prone engineering materials well
  • Prints hot and is abrasive ready at a low price
  • No chamber heater, so his deliberately hard ASA bin split
  • A full plate of tiny carbon fiber models failed twice
  • Filaments without a matching printer preset could not be printed

More from the channel: Jan 2026

Apr 1, 2026 · Sponsored by Elegoo