Skip to content

Bambu Lab A1

Owners like it. Good time to buy.

Bambu Lab A1

8.7from 9 owners
9/25

Early read. Firms up at 25 owners.

$259 was $299
13% offLowest in 90 days
Buy at Bambu Lab

Price checked Nov 9 on the official US store.

Rate yours

Owner reviews 9 Rate it (10 seconds)

Reviewers earn Spools (site points) for any review, good or bad. Spools never change a score.

T
TheImmortalSinEarned Spools November 11, 2026 (Edited)
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 7
Recommends this

would not buy again

Owned 1 to 2 years · Biggest problem: replacing the toolhead control board 4 times was kind of a downer

What I liked:

the price and ease of use

What I didn't like:

i did not like the brittle eddy current sensor standoffs on the toolhead control board

View In-Depth Breakdown

Comments (0)

O
owner-68629Earned Spools November 10, 2026
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 10
Recommends this

10/10 and would buy again

Owned 1 to 2 years · Biggest problem: None

What I liked:

What I didn't like:

Comments (0)

O
owner-85972Earned Spools November 10, 2026
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 7
Does not recommend

7/10, would not buy again

Owned 1 to 2 years

What I liked:

What I didn't like:

Comments (0)

V
VirtuconEarned Spools November 9, 2026
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 10
Recommends this

10/10 and would buy again

Owned 1 to 6 months · Biggest problem: BCMU fails to feed

What I liked:

What I didn't like:

Comments (0)

O
owner-85800Earned Spools November 9, 2026
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 8
Recommends this

8/10 and would buy again

Owned 1 to 2 years · Biggest problem: Bed slinger

What I liked:

What I didn't like:

Comments (0)

Show all 9 owner reviews
O
owner-26135Earned Spools November 9, 2026
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 8
Recommends this

8/10 and would buy again

Owned over 2 years · Biggest problem: Wear and tear. Filament hub broke. No magic smoke yet.

What I liked:

What I didn't like:

Comments (0)

M
mleppelmanEarned Spools November 9, 2026 (Edited)
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 10
Recommends this

10/10 and would buy again

Owned 1 to 2 years

What I liked:

Great printer for a bed slinger. It was my first printer and I love it.

What I didn't like:

Too much waste

Comments (0)

O
owner-12998Earned Spools November 9, 2026
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 9
Recommends this

9/10 and would buy again

Owned 1 to 2 years · Biggest problem: AMS lite feeder issues

What I liked:

What I didn't like:

Comments (0)

G
GunstarheroEarned Spools November 9, 2026
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 9
Recommends this

9/10 and would buy again

Owned 1 to 2 years · Biggest problem: This just keeps trucking along had no problems except for the fuse blowing problem but was handled great by bambu.

What I liked:

What I didn't like:

Comments (0)

Owner wall

Own one? Add yours

No verified owners yet. Post a photo of yours with your code and be the first on the wall.

Price history

Official US store, checked weekly

Good time to buy. Now $259. At or near the lowest price we have tracked. Tracked since Jun 2026.

$259 now, $90 below the median ($349)
+$50−$50+$100−$100 $349 DecJan 26FebMarAprMayJunJulAugSepOctNov +$100−$100 $349 Jan 26MarMayJulSepNov
Each week's price against the median price, lightly smoothed. Median $349, lowest $259 (week of Nov 16), highest $349, now $259 (−$90 vs median). 49 of 53 weeks are filled from launch announcements, brand sale emails or dated deal reports rather than our own store checks; hover a week to see which. Reported sales are assumed to last two weeks unless we know otherwise.
Weekly price
Week ofLowest pricevs medianSource
Nov 17, 2025$349$0dated deal report
Nov 24, 2025$349$0dated deal report
Dec 1, 2025$349$0dated deal report
Dec 8, 2025$349$0dated deal report
Dec 15, 2025$349$0dated deal report
Dec 22, 2025$349$0dated deal report
Dec 29, 2025$349$0dated deal report
Jan 5, 2026$349$0dated deal report
Jan 12, 2026$349$0dated deal report
Jan 19, 2026$349$0dated deal report
Jan 26, 2026$349$0dated deal report
Feb 2, 2026$349$0dated deal report
Feb 9, 2026$349$0dated deal report
Feb 16, 2026$349$0dated deal report
Feb 23, 2026$349$0dated deal report
Mar 2, 2026$349$0dated deal report
Mar 9, 2026$349$0dated deal report
Mar 16, 2026$349$0dated deal report
Mar 23, 2026$349$0dated deal report
Mar 30, 2026$349$0dated deal report
Apr 6, 2026$349$0dated deal report
Apr 13, 2026$349$0dated deal report
Apr 20, 2026$349$0dated deal report
Apr 27, 2026$349$0dated deal report
May 4, 2026$349$0dated deal report
May 11, 2026$349$0dated deal report
May 18, 2026$349$0dated deal report
May 25, 2026$349$0dated deal report
Jun 1, 2026$349$0dated deal report
Jun 8, 2026$349$0dated deal report
Jun 15, 2026$349$0dated deal report
Jun 22, 2026$279−$70dated deal report
Jun 29, 2026$279−$70dated deal report
Jul 6, 2026$279−$70dated deal report
Jul 13, 2026$279−$70dated deal report
Jul 20, 2026$279−$70dated deal report
Jul 27, 2026$279−$70dated deal report
Aug 3, 2026$279−$70dated deal report
Aug 10, 2026$279−$70dated deal report
Aug 17, 2026$279−$70dated deal report
Aug 24, 2026$279−$70dated deal report
Aug 31, 2026$279−$70dated deal report
Sep 7, 2026$279−$70dated deal report
Sep 14, 2026$279−$70dated deal report
Sep 21, 2026$279−$70dated deal report
Sep 28, 2026$279−$70dated deal report
Oct 5, 2026$279−$70dated deal report
Oct 12, 2026$279−$70dated deal report
Oct 19, 2026$279−$70dated deal report
Oct 26, 2026$259−$90store check
Nov 2, 2026$259−$90store check
Nov 9, 2026$259−$90store check
Nov 16, 2026$259−$90store check

Known issues 3, 1 serious

Report an issue

From brand advisories, owner forums and reviews, with sources on each. Newest first. Tap one for what happens and what fixes it.

  • High Filament blob encases hotend and breaks thermistor wires Last reported Apr 2026

    A detached print can let molten filament wrap the nozzle, heater and wiring into a blob. The exposed thermistor and heater wires on the A1 hotend are easily damaged, by the blob or during removal. One owner could not reach any screws to remove the encased hotend; another found the hotend would not heat after removing a blob, and a replacement hotend did not fix it.

    What fixes it: Good bed adhesion reduces the risk. Remove blobs slowly while the nozzle is hot and keep clear of the wires. Damaged wiring needs a replacement hotend heating assembly, and possibly further parts from support.

    From public reports: forum.bambulab.com, forum.bambulab.com · Confirm or add a fix

  • Low Asks to load and purge filament that is already loaded Last reported Nov 2026

    Since the June 2026 firmware update, A1 and A1 Mini owners say the first print after the printer sits cold acts as if new filament was just loaded: it asks for confirmation, then pushes and purges filament before starting. It wastes filament and means walking to the printer to press continue. Owners say rolling back firmware stops it.

    What fixes it: Roll back to the previous firmware. One owner fixed it by setting AMS type to "AMS 2 / H2D (Hermes)" with no AMS attached. One A1 owner says firmware 01.09.00.00 (Nov 9, 2026) fixed it; not yet confirmed by others.

    From public reports: forum.bambulab.com, forum.bambulab.com · Confirm or add a fix

  • Low Firmware authorization blocks third-party printer control Last reported Oct 2026

    Bambu's authorization control firmware requires approved software to start prints and control the printer. On updated A1 firmware, third-party tools that sent jobs or controlled the printer directly stop working unless the printer is put in LAN-only Developer Mode. Status reporting and SD card printing are unaffected.

    What fixes it: Enable LAN Only mode plus Developer Mode, use Bambu Connect, or stay on older firmware.

    From public reports: blog.bambulab.com, feedback.simplyprint.io · Confirm or add a fix

Older or fixed issues (2)
  • Critical Power board inrush thermistor can overheat and melt plastic Fixed Dec 2025

    On the original AC power distribution board, the NTC inrush-current thermistor can fail and run very hot, softening nearby parts and in some reported cases melting the printer's plastic housing. Bambu says failures are rare (about 0.05%), tied mostly to power surges, and that the part was removed and the board redesigned in Q3 2025. No fires were reported, but it drew wide attention in late 2025.

    What fixes it: Affected owners get a replacement power board from Bambu support, in or out of warranty. Bambu recommends a surge protector. Units built after Q3 2025 use the redesigned board.

    From public reports: all3dp.com, tomshardware.com, forum.bambulab.com · Confirm or add a fix

  • Critical Heatbed cable recall over electrical and fire risk Fixed Jan 2024

    In early 2024 Bambu found damage near the heatbed cable connector on some A1 units that could cause electrical failure, with at least one owner reporting the cable burning. Bambu first issued a callback in late January 2024, then extended it on Feb 4, 2024 to every A1 sold and asked owners to stop using them. Fewer than 0.1% of units had reported damage.

    What fixes it: Bambu offered a full refund or a replacement heatbed with a revised cable (about a 20 minute swap), plus store credit and extra warranty. Later production units ship with the revised cable.

    From public reports: blog.bambulab.com, forum.bambulab.com · Confirm or add a fix

Specs

A full-size open-frame bed slinger with a 256 mm cubed build volume, positioned as Bambu Lab's entry-level printer for beginners who want more space than the A1 mini. It offers automatic calibration, a quick-swap hotend, and optional four-color printing through the AMS lite.

256 × 256 × 256 mmbuild volume
Bed slinger, open frameformat
300 °Cmax nozzle
100 °Cmax bed
None (open frame)chamber
500 mm/smax speed
1 (4-color with AMS lite combo)toolheads
December 2023released

Consider instead

What the press said · 9.5 from 2 press outlets · Read them

What reviewers say 9.5 from 2

How scores work
  • 10.0 TechRadarA fast, versatile successor to the A1 Mini that is hard to fault for the money, with optional … 5/5 · Dec 2023

    A fast, versatile successor to the A1 Mini that is hard to fault for the money, with optional multi-filament printing; the open frame and software complexity are the main drawbacks.

    • Very fast printing
    • AMS Lite multi-filament option
    • Excellent build quality
    • Software can be complex
    • No enclosure
    • Bed limited to 80C

    Read the full review on TechRadar · by Alastair Jennings

  • 9.0 Tom's HardwareAn Editor's Choice pick: a reliable, quiet, high speed bed slinger at a competitive price, with the AMS … 4.5/5 · Dec 2023

    An Editor's Choice pick: a reliable, quiet, high speed bed slinger at a competitive price, with the AMS Lite an affordable way into four-color printing.

    • Fast and quiet
    • Quick-change nozzles
    • Affordable AMS Lite option
    • AMS Lite eats desk space
    • Color-change purges waste filament

    Read the full review on Tom's Hardware · by Denise Bertacchi