Needs owners3 of 5 so far
No press
Flashforge Creator 5
Not enough owners for a score yet. Here's what they say so far. Good time to buy.
2 of 5 owners · 3 more and the score goes live.
Paid link. We may earn a commission at no extra cost to you. How this works
Price checked Nov 9 on the official US store.
Owner reviews 2 Rate it (10 seconds)
Reviewers earn Spools (site points) for any review, good or bad. Spools never change a score.
Not enough owner reviews for an overall owner rating yet: 2 of 5. Every rating is shown below as it comes in. Own one? Add yours.
8/10 and would buy again
Owned 1 to 6 months · Biggest problem: Had to replace the extruder dock board. CS was great and shipping was fast.
7/10, would not buy again
Owned less than a month · Biggest problem: Inconsistent prints 50/50 on pla ,there always seems to be a problem with a print.
Comments (0)
Owner wall
Own one? Add yoursNo verified owners yet. Post a photo of yours with your code and be the first on the wall.
Price history
Official US store, checked weeklyGood time to buy. Now $699. At or near the lowest price we have tracked. Tracked since Apr 2026.
| Week of | Lowest price | vs median | Source |
|---|---|---|---|
| Apr 6, 2026 | $799 | $0 | launch price |
| Apr 13, 2026 | $799 | $0 | launch price |
| Apr 20, 2026 | $799 | $0 | launch price |
| Apr 27, 2026 | $799 | $0 | launch price |
| May 4, 2026 | $799 | $0 | store check |
| May 11, 2026 | $799 | $0 | store check |
| May 18, 2026 | $799 | $0 | store check |
| May 25, 2026 | $799 | $0 | store check |
| Jun 1, 2026 | $799 | $0 | store check |
| Jun 8, 2026 | $799 | $0 | store check |
| Jun 15, 2026 | $799 | $0 | store check |
| Jun 22, 2026 | $799 | $0 | store check |
| Jun 29, 2026 | $799 | $0 | store check |
| Jul 6, 2026 | $799 | $0 | store check |
| Jul 13, 2026 | $799 | $0 | store check |
| Jul 20, 2026 | $799 | $0 | store check |
| Jul 27, 2026 | $799 | $0 | store check |
| Aug 3, 2026 | $799 | $0 | store check |
| Aug 10, 2026 | $799 | $0 | store check |
| Aug 17, 2026 | $799 | $0 | store check |
| Aug 24, 2026 | $799 | $0 | store check |
| Aug 31, 2026 | $799 | $0 | store check |
| Sep 7, 2026 | $799 | $0 | store check |
| Sep 14, 2026 | $799 | $0 | store check |
| Sep 21, 2026 | $699 | −$100 | store check |
| Sep 28, 2026 | $699 | −$100 | store check |
| Oct 5, 2026 | $699 | −$100 | store check |
| Oct 12, 2026 | $699 | −$100 | store check |
| Oct 19, 2026 | $699 | −$100 | store check |
| Oct 26, 2026 | $699 | −$100 | store check |
| Nov 2, 2026 | $699 | −$100 | store check |
| Nov 9, 2026 | $699 | −$100 | store check |
| Nov 16, 2026 | $699 | −$100 | store check |
Known issues 2
Report an issueFrom brand advisories, owner forums and reviews, with sources on each. Newest first. Tap one for what happens and what fixes it.
-
Medium Tool pick-up and docking failures stop prints
Printer Hub collects a few Creator 5 reports of prints stopping at a tool change because a toolhead would not pick up, dock or return to its slot, shown as errors in the E0127 to E0146 range. Missing dock or carriage magnets are among the listed causes, and one owner's tool sat higher in the dock than the others so it could never be picked up. Tom's Hardware found the docking reliable in its testing.
What fixes it: Check each tool sits in its own slot, clean and check the magnets, home and retry, and update firmware (1.7.8 improved the error prompts). Printer Hub says a tool that fails from day one is a warranty case.
From public reports: printer-hub.com, support.flashforge.com · Confirm or add a fix
-
Medium Large purge waste with third-party filament
Flush volumes on the Creator 5 are tuned for Flashforge's own filament, so other brands purge far more than a toolchanger should. Tom's Hardware got a 44 g purge block for a 33 g model on defaults, and loading filament also dumped a lot of material inside the printer until firmware 1.9.4 (July 2026) moved the drop point.
What fixes it: Lower flush volumes by hand in the slicer's flush matrix and enable flushing into infill or the object. Update to firmware 1.9.4 or later so load purges drop at the rear.
From public reports: tomshardware.com, printer-hub.com · Confirm or add a fix
On KeoPrints
More from KeoPrintsNot counted in any score.
Specs
An open-frame CoreXY printer with four independent toolheads that swap automatically, so multicolor and multi-material prints happen with almost no purge waste. It suits hobbyists who want true tool-changer multicolor at a price close to AMS-style machines.
Consider instead
Needs owners3 of 5 so far
No press
Needs owners1 of 5 so far
9.02 press
What the press said · 8.0 from 1 press outlet · Read them
What reviewers say 8.0 from 1
How scores work-
8.0 Tom's HardwareThe cheapest tool changer on the market and a good entry point, though it has quirks and slicer …
The cheapest tool changer on the market and a good entry point, though it has quirks and slicer profiles that need work.
- Tool changer with low-waste printing
- Fast CoreXY
- Easy filament loading
- Open frame
- Heavy purge during loading
- Nozzle changes are difficult
Read the full review on Tom's Hardware · by Denise Bertacchi
Comments (0)
Log in to join the discussion.