Skip to content

Creality K1 Max

Not enough owners for a score yet. Here's what they say so far. Good time to buy.

Creality K1 Max

1 of 5 owners · 4 more and the score goes live.

Own one? Tap your score:
$549 was $899
39% offLowest in 90 days
Buy at Creality

Paid link. We may earn a commission at no extra cost to you. How this works

Price checked Nov 9 on the official US store.

Owner reviews 1 Rate it (10 seconds)

Reviewers earn Spools (site points) for any review, good or bad. Spools never change a score.

Not enough owner reviews for an overall owner rating yet: 1 of 5. Every rating is shown below as it comes in. Own one? Add yours.

R
Raoul525Earned Spools November 15, 2026
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 8
Recommends this

8/10 and would buy again

Owned over 2 years · Biggest problem: Occasionally I've had problems with blobs that have required significant cleaning.

What I liked:

What I didn't like:

Comments (0)

Owner wall

Own one? Add yours

No verified owners yet. Post a photo of yours with your code and be the first on the wall.

Price history

Official US store, checked weekly

Good time to buy. Now $549. At or near the lowest price we have tracked. Tracked since Nov 2025.

$549 now, $50 below the median ($599)
+$50−$50 $599 +$50 DecJan 26FebMarAprMayJunJulAugSepOctNov +$50−$50 $599 +$50 Jan 26MarMayJulSepNov
Each week's price against the median price, lightly smoothed. Median $599, lowest $549 (week of Nov 16), highest $649, now $549 (−$50 vs median).
Weekly price
Week ofLowest pricevs medianSource
Nov 17, 2025$629+$30store check
Nov 24, 2025$629+$30store check
Dec 1, 2025$629+$30store check
Dec 8, 2025$629+$30store check
Dec 15, 2025$629+$30store check
Dec 22, 2025$629+$30store check
Dec 29, 2025$629+$30store check
Jan 5, 2026$629+$30store check
Jan 12, 2026$629+$30store check
Jan 19, 2026$629+$30store check
Jan 26, 2026$629+$30store check
Feb 2, 2026$629+$30store check
Feb 9, 2026$629+$30store check
Feb 16, 2026$629+$30store check
Feb 23, 2026$629+$30store check
Mar 2, 2026$649+$50store check
Mar 9, 2026$649+$50store check
Mar 16, 2026$649+$50store check
Mar 23, 2026$649+$50store check
Mar 30, 2026$649+$50store check
Apr 6, 2026$649+$50store check
Apr 13, 2026$649+$50store check
Apr 20, 2026$599$0store check
Apr 27, 2026$599$0store check
May 4, 2026$599$0store check
May 11, 2026$549−$50store check
May 18, 2026$549−$50store check
May 25, 2026$549−$50store check
Jun 1, 2026$549−$50store check
Jun 8, 2026$649+$50store check
Jun 15, 2026$649+$50store check
Jun 22, 2026$549−$50store check
Jun 29, 2026$549−$50store check
Jul 6, 2026$549−$50store check
Jul 13, 2026$549−$50store check
Jul 20, 2026$549−$50store check
Jul 27, 2026$549−$50store check
Aug 3, 2026$549−$50store check
Aug 10, 2026$549−$50store check
Aug 17, 2026$549−$50store check
Aug 24, 2026$549−$50store check
Aug 31, 2026$549−$50store check
Sep 7, 2026$549−$50store check
Sep 14, 2026$549−$50store check
Sep 21, 2026$549−$50store check
Sep 28, 2026$549−$50store check
Oct 5, 2026$549−$50store check
Oct 12, 2026$549−$50store check
Oct 19, 2026$549−$50store check
Oct 26, 2026$549−$50store check
Nov 2, 2026$549−$50store check
Nov 9, 2026$549−$50store check
Nov 16, 2026$549−$50store check

Known issues 4

Report an issue

From brand advisories, owner forums and reviews, with sources on each. Newest first. Tap one for what happens and what fixes it.

  • Medium Firmware 1.3.5.18 breaks web printing and file access Last reported Aug 2026

    After a November 2025 update (one owner identifies it as 1.3.5.18), owners could no longer see files or start prints from the browser, and one got a false 'consumables do not match' error without using multi-color. Another reported a reboot loop. One owner said Creality pulled the release and put 1.3.3.46 back up; Creality did not confirm this in the thread.

    What fixes it: One owner fixed it by rolling back: copy the previous firmware from Creality's site to a blank USB stick and accept the install on power-up. The rollback failed or was blocked for two other owners. One owner got prints through by sending the job right after a fresh power cycle.

    From public reports: forum.creality.com · Confirm or add a fix

  • Low Built-in camera drops out or is not detected Last reported Sep 2026

    The camera works after a reboot, then shows 'rejected our connection' or 'camera not connected' within minutes or hours, often during a print. A rooted owner's logs showed the camera's USB link repeatedly disconnecting. Firmware 1.3.3.5 fixed it for one K1 owner, but others still had it on 1.3.3.8 and 1.3.3.46.

    What fixes it: Power cycling restores it temporarily. A replacement camera seemed to fix it for one owner but not for another. Reseating the cable and switching to Ethernet did not help those who tried.

    From public reports: forum.creality.com, forum.creality.com · Confirm or add a fix

  • Low Filament runout sensor gives false alarms Last reported Apr 2026

    Prints pause with 'ran out of filament' even though filament is loaded, at random points. One owner sees the opposite, a sensor that never triggers, and a replacement sensor did not change it. A factory reset and firmware update did not fix the false alarms for another owner.

    What fixes it: Unplugging the runout sensor lets prints finish, at the cost of runout detection. Unplugging it is also a suggested test for wiring versus mainboard faults.

    From public reports: forum.creality.com · Confirm or add a fix

  • Low Touchscreen dims and freezes after CFS firmware update Last reported Dec 2025

    After moving to the CFS-compatible firmware, the K1 Max screen goes dim and stops responding after it sleeps or when a print ends. A reboot clears it for a few hours. One owner says the screen works fine on older firmware, which points to software rather than the display, and a K1 owner with a CFS reports the same.

    What fixes it: Owners work around it by setting the screen to never sleep, or by toggling the screen timeout setting. One owner had no recurrence for two days after a factory reset and reflash of the latest CFS firmware. Creality has sent at least one replacement display; the owner doubted it would help.

    From public reports: forum.creality.com · Confirm or add a fix

Older or fixed issues (2)
  • High Leveling sensor errors stop prints or let the nozzle scrape the bed Last reported Jun 2025

    The strain gauge leveling system throws errors such as Key 2521, 2522 or 2529 (leveling sensor chip abnormality) and refuses to start prints, or calibration fails and the nozzle digs into the plate. It often shows up after weeks or months of normal use, and one owner saw it right after a firmware update. A K1 Max thread on it has over 23,000 views, and K1C and Ender-3 V3 owners report the same error.

    What fixes it: Owners report mixed success with a factory reset, reseating the leveling sensor cables, snugging the four bed screws, cleaning the rubber feet, and letting the bed cool before recalibrating. Creality support has sent replacement sensors under warranty, but one owner says the error came back.

    From public reports: forum.creality.com, forum.creality.com · Confirm or add a fix

  • Medium Hotend clogs and hotends that fail after a few weeks Last reported Feb 2025

    Owners describe filament jamming in the hotend or the short PTFE tube below the extruder, prints stopping after the first layer, and hotends needing replacement every few weeks. One owner said failed prints gum up the hotend and break a wire. Printing PLA with the lid on and a warm chamber is a suspected factor. A Creality moderator says the K1 and K1 Max use the same extruder.

    What fixes it: Owners suggest printing PLA with the glass lid off, lowering the retraction temperature, and replacing a deformed PTFE tube with one cut to the same length. When reseating a hotend, make sure it sits at the right height and use thermal paste on the heatsink; some owners prefer the red silicone sock hotend.

    From public reports: forum.creality.com, forum.creality.com, forum.creality.com · Confirm or add a fix

Specs

Creality's large enclosed CoreXY from the K1 line, with a 300 mm cube build volume, AI camera and LiDAR first-layer checks. Good for people who want big, fast single-color prints and an enclosure for ABS and ASA at a lower price than the K2 series.

300 × 300 × 300 mmbuild volume
CoreXY, enclosedformat
300 °Cmax nozzle
100 °Cmax bed
Passive (enclosed)chamber
600 mm/smax speed
1toolheads
Creality CFS-Cmulticolor add-on
April 2023released

Consider instead

What the press said · 9.0 from 2 press outlets · Read them

What reviewers say 9.0 from 2

How scores work
  • 9.0 Tom's HardwareAn Editor's Choice CoreXY speed machine with a big 300 mm build volume and AI sensors that catch … 4.5/5 · Oct 2023

    An Editor's Choice CoreXY speed machine with a big 300 mm build volume and AI sensors that catch failed prints.

    • Large enclosed build volume
    • Fast CoreXY printing
    • Cheaper than rivals
    • Poor filament path
    • Clunky Klipper implementation
    • Needs glue stick for adhesion

    Read the full review on Tom's Hardware · by Denise Bertacchi

  • 9.0 TechRadarAn impressive mix of speed, quality and AI features that suits a wide range of users, though filament … 4.5/5 · Sep 2023

    An impressive mix of speed, quality and AI features that suits a wide range of users, though filament loading is a hurdle for beginners.

    • AI assisted precision
    • Reliable performance
    • User friendly design
    • Awkward filament loading
    • Single filament only

    Read the full review on TechRadar · by Alastair Jennings