Skip to content

Creality Ender-5 Max

No owners yet. Here's everything else.

Creality Ender-5 Max

0 of 5 owners · 5 more and the score goes live.

Own one? Tap your score:
$749 was $849
12% off
Buy at Creality

Paid link. We may earn a commission at no extra cost to you. How this works

Price checked Nov 9 on the official US store.

Owner reviews 0 Rate it (10 seconds)

Reviewers earn Spools (site points) for any review, good or bad. Spools never change a score.

No owner reviews yet. If you own a Ender-5 Max, yours will be the first, and it starts this printer's ranking.

Owner wall

Own one? Add yours

No verified owners yet. Post a photo of yours with your code and be the first on the wall.

Price history

Official US store, checked weekly

Normal price. Now $749. About its usual $747. Tracked since Nov 2025.

$749 now, right at the median ($749)
+$50−$50 $749 DecJan 26FebMarAprMayJunJulAugSepOctNov +$50−$50 $749 Jan 26MarMayJulSepNov
Each week's price against the median price, lightly smoothed. Median $749, lowest $699 (week of Jan 5), highest $749, now $749 ($0 vs median).
Weekly price
Week ofLowest pricevs medianSource
Nov 17, 2025$749$0store check
Nov 24, 2025$749$0store check
Dec 1, 2025$749$0store check
Dec 8, 2025$749$0store check
Dec 15, 2025$749$0store check
Dec 22, 2025$699−$50store check
Dec 29, 2025$699−$50store check
Jan 5, 2026$699−$50store check
Jan 12, 2026$749$0store check
Jan 19, 2026$749$0store check
Jan 26, 2026$749$0store check
Feb 2, 2026$749$0store check
Feb 9, 2026$749$0store check
Feb 16, 2026$749$0store check
Feb 23, 2026$749$0store check
Mar 2, 2026$749$0store check
Mar 9, 2026$749$0store check
Mar 16, 2026$749$0store check
Mar 23, 2026$749$0store check
Mar 30, 2026$749$0store check
Apr 6, 2026$749$0store check
Apr 13, 2026$749$0store check
Apr 20, 2026$749$0store check
Apr 27, 2026$749$0store check
May 4, 2026$749$0store check
May 11, 2026$749$0store check
May 18, 2026$749$0store check
May 25, 2026$749$0store check
Jun 1, 2026$749$0store check
Jun 8, 2026$749$0store check
Jun 15, 2026$749$0store check
Jun 22, 2026$749$0store check
Jun 29, 2026$749$0store check
Jul 6, 2026$749$0store check
Jul 13, 2026$749$0store check
Jul 20, 2026$749$0store check
Jul 27, 2026$749$0store check
Aug 3, 2026$749$0store check
Aug 10, 2026$749$0store check
Aug 17, 2026$749$0store check
Aug 24, 2026$749$0store check
Aug 31, 2026$749$0store check
Sep 7, 2026$749$0store check
Sep 14, 2026$749$0store check
Sep 21, 2026$749$0store check
Sep 28, 2026$749$0store check
Oct 5, 2026$749$0store check
Oct 12, 2026$749$0store check
Oct 19, 2026$749$0store check
Oct 26, 2026$749$0store check
Nov 2, 2026$749$0store check
Nov 9, 2026$749$0store check
Nov 16, 2026$749$0store check

Known issues 3, 1 serious

Report an issue

From brand advisories, owner forums and reviews, with sources on each. Newest first. Tap one for what happens and what fixes it.

  • High Hotend leaks, clogs and short hotend life Last reported Aug 2026

    Owners report hotends leaking at the heater-to-heatbreak joint, clogs with PETG, and an extruder that clicks and slips after 10 to 15 minutes. One owner went through four hotends in a month and another replaces one about every 40 hours. One owner found heat shrink on the heater wires too short, leaving bare wire that could short.

    What fixes it: Owners clear clogs and replace hotends; some convert to the K2 Plus hotend using community instructions, though one still had sagging prints after. One owner fixed exposed heater wire with electrical tape or silicone gel. Replacement parts can take a week to a month to arrive.

    From public reports: forum.creality.com, forum.creality.com · Confirm or add a fix

  • Medium Leveling sensor anomaly errors during homing or calibration Last reported Oct 2026

    The printer reports a leveling sensor anomaly and the Z axis stays at the bottom or fails partway through calibration. One owner got replacement strain gauges and a mainboard from Creality without curing it; another replaced the strain gauges and heated bed. Two cases began after adding an enclosure or camera.

    What fixes it: No confirmed fix. A firmware reflash has been suggested, and a factory reset did not help one owner. Creality support sent one owner strain gauges and a mainboard.

    From public reports: forum.creality.com, forum.creality.com · Confirm or add a fix

  • Medium Toolhead ('spray head') board communication error Last reported Jun 2026

    Prints stop with 'spray head motherboard communication error'. Reseating cables or restarting helps for a print or so, then the error returns. One owner suspects a heat-related intermittent connection.

    What fixes it: No confirmed fix. A community member suggests replacing the toolhead cable, then the toolhead board, then checking the mainboard USB and power.

    From public reports: forum.creality.com · Confirm or add a fix

Older or fixed issues (1)
  • Critical Auto leveling ignored or run cold, nozzle scrapes or crashes Last reported Oct 2025

    One owner reports the stock firmware ignoring or overwriting the bed mesh so the nozzle scrapes during prints. Another says auto leveling runs at 45 °C instead of the set bed temperature, and his toolhead jammed into the bed, breaking a hotend mount and ruining part of the bed.

    What fixes it: No confirmed fix. One community member suggests rooting the printer and installing Fluidd via the community helper script for control over meshing.

    From public reports: forum.creality.com, forum.creality.com · Confirm or add a fix

Specs

A large-format open-frame CoreXY with a 400 mm cube build volume. Suits makers who need big single-piece prints like helmets or cosplay parts and do not need an enclosure out of the box.

400 × 400 × 400 mmbuild volume
CoreXY, open frameformat
300 °Cmax nozzle
100 °Cmax bed
None (open frame)chamber
700 mm/smax speed
1toolheads
February 2025released

Consider instead