8.9from 7 owners · early
9.33 press
Creality Hi
Not enough owners for a score yet. Here's what they say so far.
1 of 5 owners · 4 more and the score goes live.
Paid link. We may earn a commission at no extra cost to you. How this works
Price checked Nov 9 on the official US store.
Owner reviews 1 Rate it (10 seconds)
Reviewers earn Spools (site points) for any review, good or bad. Spools never change a score.
Not enough owner reviews for an overall owner rating yet: 1 of 5. Every rating is shown below as it comes in. Own one? Add yours.
5/10, would not buy again
Owned 6 to 12 months · Biggest problem: The matching CFS has issues with loading filament, and it doesn't like printing much harder materals over PLA. even PLA+ can have issues unless it is dried out for at least 48 hours in a med to high temp dryer
Owner wall
Own one? Add yoursNo verified owners yet. Post a photo of yours with your code and be the first on the wall.
Price history
Official US store, checked weeklyNormal price. Now $299. About its usual $298. Tracked since Nov 2025.
| Week of | Lowest price | vs median | Source |
|---|---|---|---|
| Nov 17, 2025 | $279 | −$20 | store check |
| Nov 24, 2025 | $279 | −$20 | store check |
| Dec 1, 2025 | $279 | −$20 | store check |
| Dec 8, 2025 | $279 | −$20 | store check |
| Dec 15, 2025 | $279 | −$20 | store check |
| Dec 22, 2025 | $279 | −$20 | store check |
| Dec 29, 2025 | $279 | −$20 | store check |
| Jan 5, 2026 | $279 | −$20 | store check |
| Jan 12, 2026 | $279 | −$20 | store check |
| Jan 19, 2026 | $279 | −$20 | store check |
| Jan 26, 2026 | $279 | −$20 | store check |
| Feb 2, 2026 | $279 | −$20 | store check |
| Feb 9, 2026 | $319 | +$20 | store check |
| Feb 16, 2026 | $319 | +$20 | store check |
| Feb 23, 2026 | $319 | +$20 | store check |
| Mar 2, 2026 | $319 | +$20 | store check |
| Mar 9, 2026 | $319 | +$20 | store check |
| Mar 16, 2026 | $319 | +$20 | store check |
| Mar 23, 2026 | $299 | $0 | store check |
| Mar 30, 2026 | $299 | $0 | store check |
| Apr 6, 2026 | $299 | $0 | store check |
| Apr 13, 2026 | $299 | $0 | store check |
| Apr 20, 2026 | $299 | $0 | store check |
| Apr 27, 2026 | $299 | $0 | store check |
| May 4, 2026 | $299 | $0 | store check |
| May 11, 2026 | $299 | $0 | store check |
| May 18, 2026 | $299 | $0 | store check |
| May 25, 2026 | $299 | $0 | store check |
| Jun 1, 2026 | $299 | $0 | store check |
| Jun 8, 2026 | $299 | $0 | store check |
| Jun 15, 2026 | $299 | $0 | store check |
| Jun 22, 2026 | $299 | $0 | store check |
| Jun 29, 2026 | $299 | $0 | store check |
| Jul 6, 2026 | $299 | $0 | store check |
| Jul 13, 2026 | $299 | $0 | store check |
| Jul 20, 2026 | $299 | $0 | store check |
| Jul 27, 2026 | $299 | $0 | store check |
| Aug 3, 2026 | $299 | $0 | store check |
| Aug 10, 2026 | $299 | $0 | store check |
| Aug 17, 2026 | $299 | $0 | store check |
| Aug 24, 2026 | $299 | $0 | store check |
| Aug 31, 2026 | $299 | $0 | store check |
| Sep 7, 2026 | $299 | $0 | store check |
| Sep 14, 2026 | $299 | $0 | store check |
| Sep 21, 2026 | $299 | $0 | store check |
| Sep 28, 2026 | $299 | $0 | store check |
| Oct 5, 2026 | $299 | $0 | store check |
| Oct 12, 2026 | $299 | $0 | store check |
| Oct 19, 2026 | $299 | $0 | store check |
| Oct 26, 2026 | $299 | $0 | store check |
| Nov 2, 2026 | $299 | $0 | store check |
| Nov 9, 2026 | $299 | $0 | store check |
| Nov 16, 2026 | $299 | $0 | store check |
Known issues 4, 1 serious
Report an issueFrom brand advisories, owner forums and reviews, with sources on each. Newest first. Tap one for what happens and what fixes it.
-
High Recurring extruder jams and clogs
Owners report the extruder jamming every few weeks or more often, with the printer moving but extruding nothing. One owner's jam pushed off the silicone sock, filled the hotend area and broke the temperature sensor leads. Cleaning and part replacements have only helped temporarily for some.
What fixes it: Owners clean the extruder and hotend and suggest sticking to PLA where possible, not overtightening the nozzle, and not closing a soft enclosure over the printer. One theory is a cut fragment left in the nozzle at color changes. No confirmed fix.
From public reports: forum.creality.com, forum.creality.com, forum.creality.com · Confirm or add a fix
-
Medium Worn or stuck cutter leaves filament in the path (FR2849)
On long multicolor prints, one owner found a dull cutter blade leaving filament partly cut and an FR2849 retract error. Another had a fragment lodged in the cutter gears, and an owner warns that an overtightened nozzle can block the cutter arm.
What fixes it: Owners suggest replacing the cutter blade (one found third-party blades had reversed magnet polarity), making sure the cutter arm returns freely, and not overtightening the nozzle. No outcome was reported for these fixes.
From public reports: forum.creality.com, forum.creality.com, forum.creality.com · Confirm or add a fix
-
Medium CFS buffer stops feeding during prints
Loading from the screen works but during printing the buffer flag drops, the CFS stops pushing and the extruder slips. One owner replaced the buffer and updated firmware without a fix; another replaced the extruder and cables and tried several firmware versions without a fix.
What fixes it: Check that PTFE tubes are seated at the buffer. No confirmed fix yet.
From public reports: forum.creality.com · Confirm or add a fix
-
Low Camera view broke in Creality Print after firmware 1.1.0.72
After firmware 1.1.0.72 (June 2026) several owners found the camera feed stuck loading in Creality Print on Windows, though it still worked in the app and browser. One also reported wall artifacts.
What fixes it: Roll back to 1.1.0.65, or view the camera in Creality Cloud or a browser.
From public reports: forum.creality.com, forum.creality.com · Confirm or add a fix
Specs
An open-frame bed slinger from Creality with a 260 × 260 × 300 mm build volume, step-servo X/Y motors, a quick-swap nozzle and RFID filament reading. Designed for home users who want a simple single-color printer that can add the CFS for multi-color printing.
Consider instead
8.9from 7 owners · early
9.33 press
8.7from 9 owners · early
9.52 press
Needs owners2 of 5 so far
8.52 press
What the press said · 7.5 from 2 press outlets · Read them
What reviewers say 7.5 from 2
How scores work-
8.0 TechRadarAn exceptionally good value entry-level printer with expandable multi-color support, best for beginners and hobbyists who do not …
An exceptionally good value entry-level printer with expandable multi-color support, best for beginners and hobbyists who do not need tight dimensional accuracy.
- Exceptional value, expandable to 16 colors
- Sturdy, nearly pre-assembled metal build
- Strong bed adhesion
- Slow, wasteful multicolor printing
- Weak dimensional accuracy
- Clearing clogs is fiddly
Read the full review on TechRadar · by Alastair Jennings
-
7.0 Tom's HardwareA well-built four-color bedslinger, but priced above rivals without clearly beating them, so it mainly makes sense for …
A well-built four-color bedslinger, but priced above rivals without clearly beating them, so it mainly makes sense for buyers already in the Creality ecosystem.
- Four-color material system
- Fast printing and roomy build volume
- Reliable auto bed leveling
- High-flow hotend creates lots of purge waste
- Cannot print TPU
Read the full review on Tom's Hardware · by Denise Bertacchi
KeoPrints review
Not counted in the Internet scoreKeo expected little more than a cheaper Bambu A1 but says he was pleasantly surprised: the Creality Hi was very plug and play and printed well straight out of the box. He calls it a pretty good machine with impressive quality and attention to detail, while noting he has not printed long enough to judge long-term reliability.
Pros, cons and the video
- Fast assembly in about 15 minutes with clear in-box instructions
- Excellent epoxy build plate adhesion with no failed models on a full multicolor plate
- Clean color changes, and the CFS adds a screen and tube access cutouts
- More ringing on surfaces than his X1 Carbon
- Clunky menus for mapping CFS filament colors
- Rough top surfaces, and the app never detected the camera
Mar 24, 2025
Comments (0)
Log in to join the discussion.