Skip to content

Creality SPARKX i7

No owners yet. Here's everything else.

Replaced by the Creality SPARKX i8.

Creality SPARKX i7

0 of 5 owners · 5 more and the score goes live.

Own one? Tap your score:
$279
Buy at Creality

Paid link. We may earn a commission at no extra cost to you. How this works

Price checked Nov 9 on the official US store.

Owner reviews 0 Rate it (10 seconds)

Reviewers earn Spools (site points) for any review, good or bad. Spools never change a score.

No owner reviews yet. If you own a SPARKX i7, yours will be the first, and it starts this printer's ranking.

Owner wall

Own one? Add yours

No verified owners yet. Post a photo of yours with your code and be the first on the wall.

Price history

Official US store, checked weekly

Good price. Now $279. Below its usual $306. Tracked since Jan 2026.

$279 now, right at the median ($279)
+$50−$50+$100−$100+$150−$150 $279 +$120 Jan 26FebMarAprMayJunJulAugSepOctNov +$100−$100 $279 +$120 Jan 26MarMayJulSepNov
Each week's price against the median price, lightly smoothed. Median $279, lowest $229 (week of Sep 7), highest $399, now $279 ($0 vs median).
Weekly price
Week ofLowest pricevs medianSource
Jan 5, 2026$339+$60store check
Jan 12, 2026$339+$60store check
Jan 19, 2026$339+$60store check
Jan 26, 2026$399+$120store check
Feb 2, 2026$399+$120store check
Feb 9, 2026$399+$120store check
Feb 16, 2026$399+$120store check
Feb 23, 2026$399+$120store check
Mar 2, 2026$399+$120store check
Mar 9, 2026$399+$120store check
Mar 16, 2026$399+$120store check
Mar 23, 2026$399+$120store check
Mar 30, 2026$279$0store check
Apr 6, 2026$279$0store check
Apr 13, 2026$279$0store check
Apr 20, 2026$359+$80store check
Apr 27, 2026$359+$80store check
May 4, 2026$279$0store check
May 11, 2026$279$0store check
May 18, 2026$279$0store check
May 25, 2026$279$0store check
Jun 1, 2026$279$0store check
Jun 8, 2026$279$0store check
Jun 15, 2026$279$0store check
Jun 22, 2026$279$0store check
Jun 29, 2026$279$0store check
Jul 6, 2026$279$0store check
Jul 13, 2026$279$0store check
Jul 20, 2026$229−$50store check
Jul 27, 2026$229−$50store check
Aug 3, 2026$229−$50store check
Aug 10, 2026$229−$50store check
Aug 17, 2026$229−$50store check
Aug 24, 2026$229−$50store check
Aug 31, 2026$229−$50store check
Sep 7, 2026$229−$50store check
Sep 14, 2026$279$0store check
Sep 21, 2026$279$0store check
Sep 28, 2026$279$0store check
Oct 5, 2026$279$0store check
Oct 12, 2026$279$0store check
Oct 19, 2026$279$0store check
Oct 26, 2026$279$0store check
Nov 2, 2026$279$0store check
Nov 9, 2026$279$0store check
Nov 16, 2026$279$0store check

Known issues 4

Report an issue

From brand advisories, owner forums and reviews, with sources on each. Newest first. Tap one for what happens and what fixes it.

  • Medium Problems reported after a recent firmware update Last reported Nov 2026

    In September 2026 one owner said AI spaghetti detection stopped working after the latest update, and another said an update made both of his printers glitch with failed prints. Version numbers were not given.

    What fixes it: One owner says a later firmware update fixed the glitch. Some owners are holding off on updates.

    From public reports: forum.creality.com, forum.creality.com · Confirm or add a fix

  • Medium Uneven bed mesh causes first-layer and adhesion failures Last reported Nov 2026

    Owners report bed meshes with roughly 0.7 to 1.0 mm of variation, tilted or warped beds, and parts detaching or first layers not sticking even on default settings.

    What fixes it: Owners check the mesh in Fluidd, level the four corners with the bed screws, check X-axis and X-to-Z screws for looseness, and in one case shim under the plate with foil. One owner got the mesh down to about 0.3 mm this way; another could not get below 0.7 mm. It can take hours.

    From public reports: forum.creality.com, forum.creality.com, forum.creality.com, forum.creality.com · Confirm or add a fix

  • Medium CFS Lite does not fully retract at color changes Last reported Oct 2026

    Owners find filament is not pulled back to the CFS Lite at a color change, or a swap cuts three times then fails with TR2963. One owner relays a Creality livestream saying the CFS Lite only retracts clear of the hotend by design, so part of this may be expected behavior.

    What fixes it: One owner starts a load, waits for retraction to begin, then pulls the old filament out by hand, and restarts if the light flashes red. For TR2963, pressing OK then Proceed completes the swap but wastes filament. No official fix.

    From public reports: forum.creality.com, forum.creality.com · Confirm or add a fix

  • Medium Clogs leave the nozzle stuck in the hotend Last reported Sep 2026

    After a clog or blob, owners cannot pull the quick-swap nozzle out even when hot, and one had to use pliers, bending the tube.

    What fixes it: Owners suggest removing the silicone sock, heating to about 240 C and pushing filament through with a needle, or cycling temperatures until it releases. None of these was confirmed to work; one owner was offered a replacement printer by Creality.

    From public reports: forum.creality.com, forum.creality.com · Confirm or add a fix

Specs

A compact open-frame bed slinger from Creality with a 260 × 260 × 255 mm build volume, quick-swap 300 °C hotend, built-in AI camera and a quiet night mode. Aimed at beginners and home users, with an optional CFS Lite unit for up to four-color printing.

260 × 260 × 255 mmbuild volume
Bed slinger, open frameformat
300 °Cmax nozzle
100 °Cmax bed
None (open frame)chamber
500 mm/smax speed
1 (4-color with CFS Lite combo)toolheads
January 2026released

Consider instead

What the press said · 8.8 from 2 press outlets · Read them

What reviewers say 8.8 from 2

How scores work
  • 9.0 Tom's HardwareAn Editor's Choice entry-level four-color printer at an affordable price, with a CFS Lite spool system that needs … 4.5/5 · Jan 2026

    An Editor's Choice entry-level four-color printer at an affordable price, with a CFS Lite spool system that needs very little upkeep.

    • Low-maintenance CFS Lite
    • Fast and quiet
    • Good interface and auto leveling
    • Lengthy privacy policy at setup
    • CFS Lite does not retract spools

    Read the full review on Tom's Hardware · by Denise Bertacchi

  • 8.5 CGMagazineA worthwhile buy for anyone wanting an easy multicolor printer, with quick setup, smart filament storage and reliable … 8.5/10 · May 2026

    A worthwhile buy for anyone wanting an easy multicolor printer, with quick setup, smart filament storage and reliable local or remote printing.

    • Ready to print in about 20 minutes
    • Moisture-proof RFID filament case
    • Quiet mode suits overnight prints
    • Single LED is too dim
    • Remote camera feed sometimes slow to connect

    Read the full review on CGMagazine · by Matt Keith

KeoPrints review

Not counted in the Internet score

Keo's take

Keo's first take is that the SPARKX i7 is fine: not mind-blowing, made of cheap plastic, but priced where it should be and performing as it should out of the box. He says it is not a full review and, since Creality supplied the machine, he will not tell viewers to buy it yet.

Pros, cons and the video
  • Arrives fully assembled and is printing quickly
  • Clean first multicolor print and a full plate of tiny models with no failures
  • CFS Lite keeps four spools enclosed and reads RFID tags
  • One CFS Lite feeder lane did not work out of the box
  • Cheap plastic parts that flex
  • Slicer bogs down with many models, and abrasive and soft TPU support is limited

Jun 22, 2026 · Printer provided by Creality