Skip to content

Original Prusa MINI+

No owners yet. Here's everything else.

Original Prusa MINI+

0 of 5 owners · 5 more and the score goes live.

Own one? Tap your score:
$549
Buy at Prusa

Price checked Nov 9 on the official US store.

Owner reviews 0 Rate it (10 seconds)

Reviewers earn Spools (site points) for any review, good or bad. Spools never change a score.

No owner reviews yet. If you own a MINI+, yours will be the first, and it starts this printer's ranking.

Owner wall

Own one? Add yours

No verified owners yet. Post a photo of yours with your code and be the first on the wall.

Price history

Official US store, checked weekly

Normal price. Now $549. About its usual $548. Tracked since Aug 2026.

$549 now, right at the median ($549)
+$50−$50 $549 SepOctNov +$50−$50 $549 SepNov
Each week's price against the median price, lightly smoothed. Median $549, lowest $508 (week of Oct 26), highest $549, now $549 ($0 vs median).
Weekly price
Week ofLowest pricevs medianSource
Aug 31, 2026$549$0store check
Sep 7, 2026$549$0store check
Sep 14, 2026$549$0store check
Sep 21, 2026$549$0store check
Sep 28, 2026$549$0store check
Oct 5, 2026$549$0store check
Oct 12, 2026$549$0store check
Oct 19, 2026$549$0store check
Oct 26, 2026$508.33−$41store check
Nov 2, 2026$549$0store check
Nov 9, 2026$549$0store check
Nov 16, 2026$549$0store check

Known issues 3, 1 serious

Report an issue

From brand advisories, owner forums and reviews, with sources on each. Newest first. Tap one for what happens and what fixes it.

  • High Thermal runaway errors after firmware 8.0.0 Last reported Oct 2026

    After updating to firmware 8.0.0, MINI and MINI+ owners get thermal runaway errors that stop prints. One owner's logged temperatures looked normal, while another saw the nozzle running hot and fluctuating, and some saw it on 7.0.0 too. Prusa staff said on the forum that it is under investigation and advised rolling back.

    What fixes it: Prusa staff recommend rolling back to firmware 6.4.2 until a fix ships; three owners confirm the rollback stopped the errors.

    From public reports: forum.prusa3d.com, forum.prusa3d.com · Confirm or add a fix

  • Medium Worn PTFE tubes cause under-extrusion and stringing Last reported Jun 2026

    On MINIs with heavy use, the PTFE tubes wear inside, leading to under-extrusion, stringing, seams and weak or separated layers. Two owners fixed this by replacing a worn Bowden tube. One owner running three MINIs for about 7,000 hours each suggests replacing the hotend PTFE tube about every 1,000 hours and the other PTFE tubes about every 3,000 hours; as of mid 2025 Prusa's maintenance page did not list intervals.

    What fixes it: Replace the Bowden tube (one owner used 1.9 mm ID) and the hotend PTFE tube when worn. One owner saw their pressure advance value drop from 0.28 to 0.1 after a new Bowden tube.

    From public reports: forum.prusa3d.com, forum.prusa3d.com · Confirm or add a fix

  • Low Wi-Fi through the ESP-01S module is flaky Last reported Jun 2026

    The MINI+ relies on a small add-on ESP-01S module for Wi-Fi, and owners report failed module flashing, connections that only work some of the time, and trouble with mixed 2.4/5 GHz networks. Prusa's staff-run troubleshooting thread launched with a firmware release described as a beta for experienced users. A 2026 thread reports a generic module stuck scanning.

    What fixes it: Connect the module to the 2.4 GHz band, avoid leading spaces and special characters in the network name and password, and force the module update at startup if flashing stalls.

    From public reports: forum.prusa3d.com, forum.prusa3d.com · Confirm or add a fix

Specs

The MINI+ is Prusa's small, low-cost bed slinger with a 180 mm cube build area, a removable PEI sheet and a filament sensor. It suits first-time buyers or a second desk printer for small parts, but it is slow and basic next to newer budget machines.

180 × 180 × 180 mmbuild volume
Bed slinger, open frameformat
280 °Cmax nozzle
100 °Cmax bed
None (open frame)chamber
1toolheads
November 2020released

Consider instead

What the press said · 8.5 from 2 press outlets · Read them

What reviewers say 8.5 from 2

How scores work
  • 9.0 Tom's GuideAn Editor's Choice beginner printer that costs more than budget options but is more capable and reliable, with … 4.5/5 · Nov 2022

    An Editor's Choice beginner printer that costs more than budget options but is more capable and reliable, with better output than most entry-level machines.

    • Simple assembly and setup
    • Excellent software
    • Very strong print quality
    • Costs more than many beginner printers
    • No remote control or monitoring

    Read the full review on Tom's Guide · by Richard Baguley

  • 8.0 Tom's HardwareA small printer that delivers professional quality results and is approachable for newcomers, backed by a strong community. 4/5 · May 2021

    A small printer that delivers professional quality results and is approachable for newcomers, backed by a strong community.

    • Easy setup
    • High quality prints
    • Auto leveling with magnetic sheets
    • Small build volume
    • Pricey for its size

    Read the full review on Tom's Hardware · by Ash Hill