Skip to content

QIDI Plus5

No owners yet. Here's everything else. Good time to buy.

QIDI Plus5

0 of 5 owners · 5 more and the score goes live.

Own one? Tap your score:
$699 was $749
7% offLowest in 90 days
Buy at QIDI

Paid link. We may earn a commission at no extra cost to you. How this works

Price checked Nov 7 on the official US store.

Owner reviews 0 Rate it (10 seconds)

Reviewers earn Spools (site points) for any review, good or bad. Spools never change a score.

No owner reviews yet. If you own a Plus5, yours will be the first, and it starts this printer's ranking.

Owner wall

Own one? Add yours

No verified owners yet. Post a photo of yours with your code and be the first on the wall.

Price history

Official US store, checked weekly

Good time to buy. Now $699. At or near the lowest price we have tracked. Tracked since Aug 2026.

$699 now, $50 below the median ($749)
+$50−$50 $749 AugSepOctNov +$50−$50 $749 SepNov
Each week's price against the median price, lightly smoothed. Median $749, lowest $699 (week of Nov 16), highest $749, now $699 (−$50 vs median).
Weekly price
Week ofLowest pricevs medianSource
Aug 3, 2026$749$0store check
Aug 10, 2026$749$0store check
Aug 17, 2026$749$0store check
Aug 24, 2026$749$0store check
Aug 31, 2026$749$0store check
Sep 7, 2026$749$0store check
Sep 14, 2026$749$0store check
Sep 21, 2026$749$0store check
Sep 28, 2026$749$0store check
Oct 5, 2026$749$0store check
Oct 12, 2026$749$0store check
Oct 19, 2026$749$0store check
Oct 26, 2026$749$0store check
Nov 2, 2026$699−$50store check
Nov 9, 2026$699−$50store check
Nov 16, 2026$699−$50store check

Known issues 5

Report an issue

From brand advisories, owner forums and reviews, with sources on each. Newest first. Tap one for what happens and what fixes it.

  • Medium Uneven bed temperature causes edge warping on large parts Last reported Nov 2026

    The bed edges run cooler than the center. One review measured up to 8.6 °C of deviation at 60 °C and up to 17 °C at 90 °C and tied it to warped ASA edges; another measured about 6 °C between center and edge at 50 °C and saw slight corner warping on an ABS test cube.

    What fixes it: Preheat the chamber before ABS or ASA prints; this removed the corner warping in one review.

    From public reports: china-gadgets.de, smartzone.de · Confirm or add a fix

  • Medium No clog detection unless the QIDI Box is connected Last reported Oct 2026

    3DWork reports that without the optional QIDI Box the printer does not detect filament jams, so a jammed hotend can go unnoticed. A known-issues roundup says QIDI's spec lists tangle detection as requiring the Box.

    What fixes it: Adding the QIDI Box adds jam detection, according to 3DWork.

    From public reports: 3dwork.io, nikktech.com, printer-hub.com · Confirm or add a fix

  • Medium PLA jams and mushy prints with the lid closed Last reported Oct 2026

    With the glass lid shut, heat builds in the chamber and PLA softens too early in the hotend, giving mushy prints or full jams. Two independent reviews hit this on PLA shortly after the August 2026 launch, and a known-issues roundup adds owner reports, including one PETG jam in a closed chamber.

    What fixes it: Slide the top glass back for PLA; both reviews only got good PLA prints that way.

    From public reports: 3dwork.io, china-gadgets.de, printer-hub.com · Confirm or add a fix

  • Low PTFE tube knocks against the glass lid Last reported Nov 2026

    The extruder feed tube arcs high enough to tap the top glass during fast moves, and owners also report it catching the lid handle screws. Reported by one review and by owners in two Reddit threads.

    What fixes it: Put a small piece of tape or a soft pad on the tube where it hits, or print the riser listed on QIDI's Printable Components page for the Plus5.

    From public reports: smartzone.de, printer-hub.com · Confirm or add a fix

  • Low Large purge at the start of every print Last reported Oct 2026

    The machine purges a lot of filament before each print and on load and unload, even without the Box, and 3DWork found no setting on the printer to reduce it. An owner in a Reddit thread called it insanely high and wasteful.

    What fixes it: Reduce the purge in the slicer profile. QIDI's firmware 01.01.01.06 reduced purging during print recovery, but not the start-of-print purge.

    From public reports: 3dwork.io, printer-hub.com · Confirm or add a fix

On KeoPrints

More from KeoPrints

Not counted in any score.

Specs

A larger enclosed CoreXY printer with a 65 °C heated chamber and a 370 °C hotend, replacing the Plus4. It suits makers who print engineering materials like ABS, ASA, nylon and carbon-fiber blends and want a big build volume for the money.

320 × 320 × 300 mmbuild volume
CoreXY, enclosedformat
370 °Cmax nozzle
120 °Cmax bed
65 °C (active heating)chamber
600 mm/smax speed
1toolheads
QIDI Boxmulticolor add-on
Plus4 Plus5replaces
August 2026released

Consider instead

What the press said · 9.0 from 1 press outlet · Read them

What reviewers say 9.0 from 1

How scores work
  • 9.0 Tom's HardwareAn Editor's Choice and the best QIDI tested, great for large high-temp prints thanks to its heated chamber, … 4.5/5 · Aug 2026

    An Editor's Choice and the best QIDI tested, great for large high-temp prints thanks to its heated chamber, but the optional QIDI Box still does not work well.

    • Heated chamber
    • HEPA filtration
    • Polished hardware and software with little setup
    • Awkward rear filament loading
    • QIDI Box multimaterial still unreliable

    Read the full review on Tom's Hardware · by Denise Bertacchi