Creality K1 Max known issues
What owners run into, most important first. Issues marked "from public reports" come from brand advisories, owner forums and reviews, linked on each one.
-
Medium Firmware 1.3.5.18 breaks web printing and file access
After a November 2025 update (one owner identifies it as 1.3.5.18), owners could no longer see files or start prints from the browser, and one got a false 'consumables do not match' error without using multi-color. Another reported a reboot loop. One owner said Creality pulled the release and put 1.3.3.46 back up; Creality did not confirm this in the thread.
What fixes it: One owner fixed it by rolling back: copy the previous firmware from Creality's site to a blank USB stick and accept the install on power-up. The rollback failed or was blocked for two other owners. One owner got prints through by sending the job right after a fresh power cycle.
From public reports: forum.creality.com · Confirm or add a fix
-
Low Built-in camera drops out or is not detected
The camera works after a reboot, then shows 'rejected our connection' or 'camera not connected' within minutes or hours, often during a print. A rooted owner's logs showed the camera's USB link repeatedly disconnecting. Firmware 1.3.3.5 fixed it for one K1 owner, but others still had it on 1.3.3.8 and 1.3.3.46.
What fixes it: Power cycling restores it temporarily. A replacement camera seemed to fix it for one owner but not for another. Reseating the cable and switching to Ethernet did not help those who tried.
From public reports: forum.creality.com, forum.creality.com · Confirm or add a fix
-
Low Filament runout sensor gives false alarms
Prints pause with 'ran out of filament' even though filament is loaded, at random points. One owner sees the opposite, a sensor that never triggers, and a replacement sensor did not change it. A factory reset and firmware update did not fix the false alarms for another owner.
What fixes it: Unplugging the runout sensor lets prints finish, at the cost of runout detection. Unplugging it is also a suggested test for wiring versus mainboard faults.
From public reports: forum.creality.com · Confirm or add a fix
-
High Leveling sensor errors stop prints or let the nozzle scrape the bed
The strain gauge leveling system throws errors such as Key 2521, 2522 or 2529 (leveling sensor chip abnormality) and refuses to start prints, or calibration fails and the nozzle digs into the plate. It often shows up after weeks or months of normal use, and one owner saw it right after a firmware update. A K1 Max thread on it has over 23,000 views, and K1C and Ender-3 V3 owners report the same error.
What fixes it: Owners report mixed success with a factory reset, reseating the leveling sensor cables, snugging the four bed screws, cleaning the rubber feet, and letting the bed cool before recalibrating. Creality support has sent replacement sensors under warranty, but one owner says the error came back.
From public reports: forum.creality.com, forum.creality.com · Confirm or add a fix
-
Low Touchscreen dims and freezes after CFS firmware update
After moving to the CFS-compatible firmware, the K1 Max screen goes dim and stops responding after it sleeps or when a print ends. A reboot clears it for a few hours. One owner says the screen works fine on older firmware, which points to software rather than the display, and a K1 owner with a CFS reports the same.
What fixes it: Owners work around it by setting the screen to never sleep, or by toggling the screen timeout setting. One owner had no recurrence for two days after a factory reset and reflash of the latest CFS firmware. Creality has sent at least one replacement display; the owner doubted it would help.
From public reports: forum.creality.com · Confirm or add a fix
-
Medium Hotend clogs and hotends that fail after a few weeks
Owners describe filament jamming in the hotend or the short PTFE tube below the extruder, prints stopping after the first layer, and hotends needing replacement every few weeks. One owner said failed prints gum up the hotend and break a wire. Printing PLA with the lid on and a warm chamber is a suspected factor. A Creality moderator says the K1 and K1 Max use the same extruder.
What fixes it: Owners suggest printing PLA with the glass lid off, lowering the retraction temperature, and replacing a deformed PTFE tube with one cut to the same length. When reseating a hotend, make sure it sits at the right height and use thermal paste on the heatsink; some owners prefer the red silicone sock hotend.
From public reports: forum.creality.com, forum.creality.com, forum.creality.com · Confirm or add a fix