Skip to content

Creality K2 Plus

Not enough owners for a score yet. Here's what they say so far.

Creality K2 Plus

1 of 5 owners · 4 more and the score goes live.

Own one? Tap your score:
$999 was $1,299
23% off
Buy at Creality

Paid link. We may earn a commission at no extra cost to you. How this works

Price checked Nov 9 on the official US store.

Owner reviews 1 Rate it (10 seconds)

Reviewers earn Spools (site points) for any review, good or bad. Spools never change a score.

Not enough owner reviews for an overall owner rating yet: 1 of 5. Every rating is shown below as it comes in. Own one? Add yours.

O
owner-19837Earned Spools November 9, 2026
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ 10
Recommends this

10/10 and would buy again

Owned 1 to 2 years

What I liked:

What I didn't like:

Comments (0)

Owner wall

Own one? Add yours

No verified owners yet. Post a photo of yours with your code and be the first on the wall.

Price history

Official US store, checked weekly

Normal price. Now $999. About its usual $1,048. Tracked since Nov 2025.

$999 now, right at the median ($999)
+$100−$100+$200−$200 $999 +$200 DecJan 26FebMarAprMayJunJulAugSepOctNov +$200−$200 $999 +$200 Jan 26MarMayJulSepNov
Each week's price against the median price, lightly smoothed. Median $999, lowest $899 (week of Sep 14), highest $1,199, now $999 ($0 vs median).
Weekly price
Week ofLowest pricevs medianSource
Nov 17, 2025$999$0store check
Nov 24, 2025$999$0store check
Dec 1, 2025$999$0store check
Dec 8, 2025$999$0store check
Dec 15, 2025$999$0store check
Dec 22, 2025$999$0store check
Dec 29, 2025$1,099+$100store check
Jan 5, 2026$1,099+$100store check
Jan 12, 2026$1,099+$100store check
Jan 19, 2026$1,099+$100store check
Jan 26, 2026$1,099+$100store check
Feb 2, 2026$1,099+$100store check
Feb 9, 2026$1,099+$100store check
Feb 16, 2026$1,099+$100store check
Feb 23, 2026$1,099+$100store check
Mar 2, 2026$1,099+$100store check
Mar 9, 2026$1,099+$100store check
Mar 16, 2026$1,099+$100store check
Mar 23, 2026$1,099+$100store check
Mar 30, 2026$1,099+$100store check
Apr 6, 2026$1,099+$100store check
Apr 13, 2026$1,099+$100store check
Apr 20, 2026$1,099+$100store check
Apr 27, 2026$999$0store check
May 4, 2026$999$0store check
May 11, 2026$999$0store check
May 18, 2026$1,199+$200store check
May 25, 2026$1,199+$200store check
Jun 1, 2026$1,099+$100store check
Jun 8, 2026$1,099+$100store check
Jun 15, 2026$1,099+$100store check
Jun 22, 2026$1,099+$100store check
Jun 29, 2026$1,099+$100store check
Jul 6, 2026$1,099+$100store check
Jul 13, 2026$999$0store check
Jul 20, 2026$999$0store check
Jul 27, 2026$999$0store check
Aug 3, 2026$999$0store check
Aug 10, 2026$899−$100store check
Aug 17, 2026$899−$100store check
Aug 24, 2026$899−$100store check
Aug 31, 2026$899−$100store check
Sep 7, 2026$899−$100store check
Sep 14, 2026$899−$100store check
Sep 21, 2026$999$0store check
Sep 28, 2026$999$0store check
Oct 5, 2026$999$0store check
Oct 12, 2026$999$0store check
Oct 19, 2026$999$0store check
Oct 26, 2026$999$0store check
Nov 2, 2026$999$0store check
Nov 9, 2026$999$0store check
Nov 16, 2026$999$0store check

Known issues 5, 3 serious

Report an issue

From brand advisories, owner forums and reviews, with sources on each. Newest first. Tap one for what happens and what fixes it.

  • Critical Nozzle drives into the bed during leveling (strain gauge faults) Last reported Sep 2026

    During pre-print probing, some printers keep raising the bed until it hits the nozzle, or slam the bed repeatedly, then stop with CM2789 or another error. Owners traced it to a failed strain gauge, pinched toolhead wiring, or a damaged extruder board. One owner had bent guides after the extruder hit the bed.

    What fixes it: Replacing the strain gauge and fixing pinched toolhead wires worked for one owner; another saw the fault return after about 20 prints with a new strain gauge. A community member suggests sending support a video with the serial number.

    From public reports: forum.creality.com, forum.creality.com · Confirm or add a fix

  • High CFS fails to retract or feed filament at color changes Last reported Aug 2026

    At a color change the filament does not pull back to the CFS, or the new filament never reaches the extruder, and the printer flags a clog or a feed error such as FR2836. It has been reported since late 2024 and was still being reported in 2026. Replacement extruders from Creality did not cure it for at least two owners.

    What fixes it: Owners report checking for a missing cutter rod and loose rail screws, clearing metal debris from the cutter magnet (which fixed it for one owner), fitting a printed spacer behind the cutter arm, and reseating the CFS hub as a temporary workaround. Results are mixed and no official fix has been announced.

    From public reports: forum.creality.com, forum.creality.com, forum.creality.com · Confirm or add a fix

  • High Extruder motor stops or extruder clogs with no extrusion Last reported Aug 2026

    Owners report the extruder stopping with no extrusion, including one whose extruder motor stopped entirely with no error even after reseating cables and updating firmware. Others report PETG softening in the extruder gears and clogging.

    What fixes it: Creality support offered one owner a replacement motor after receiving videos through live chat. For PETG clogs, owners suggest printing around 230 C and calibrating flow.

    From public reports: forum.creality.com, forum.creality.com · Confirm or add a fix

  • Medium Inconsistent first layer from bed warp and noisy bed mesh Last reported Nov 2026

    Owners see uneven first layers across the large bed. One owner measured about 0.5 mm of bed deformation when hot, and another found repeated probes of the same spot varied by up to about 0.07 mm, about a third of a 0.2 mm layer. That owner also says the firmware ignores the probe samples setting.

    What fixes it: Owners have tried heat soaking the bed before probing, a finer mesh, and averaging several mesh runs into a saved mesh. Results are mixed: heat soaking made it worse for one owner and a finer mesh did not help another. One owner reports good results after switching to an aftermarket graphite bed.

    From public reports: forum.creality.com, forum.creality.com · Confirm or add a fix

  • Medium Filament cutter does not fully cut, causing jams and FR2865 Last reported Jan 2026

    The toolhead cutter sometimes leaves filament partly attached or with a melted tip, which jams the extruder or triggers FR2865 (filament failed to exit extruder) at the end of a print. One owner tied it to cutter travel tolerance exposed by newer firmware.

    What fixes it: Replace the cutter blade, then run the full calibration including cutter calibration. Some owners fit a printed cutter rod spacer, with mixed results.

    From public reports: forum.creality.com, forum.creality.com · Confirm or add a fix

Specs

Creality's largest K2-series enclosed CoreXY printer, with a 350 mm cube build volume, a 60 °C actively heated chamber, and a 350 °C hardened-steel hotend. Built for makers printing large parts or engineering filaments; pairs with the CFS for multi-color work.

350 × 350 × 350 mmbuild volume
CoreXY, enclosedformat
350 °Cmax nozzle
120 °Cmax bed
60 °C (active heating)chamber
600 mm/smax speed
1 (4-color with CFS combo)toolheads
Creality CFSmulticolor add-on
July 2024released

Consider instead

What the press said · 9.0 from 2 press outlets · Read them

What reviewers say 9.0 from 2

How scores work
  • 9.0 TechRadarA well built, feature packed large-format machine with excellent output and broad material support; a bit pricier than … 4.5/5 · Mar 2025

    A well built, feature packed large-format machine with excellent output and broad material support; a bit pricier than other multi-filament options but worth it.

    • Large build area
    • Fast CoreXY printing
    • Reasonable multi-filament speed
    • Multi-filament still slower than some rivals
    • Big footprint

    Read the full review on TechRadar · by Alastair Jennings

  • 9.0 Tom's HardwareMore than a Bambu X1C clone: the reviewer judged it better, with a larger heated chamber, easier spool … 4.5/5 · Jan 2025

    More than a Bambu X1C clone: the reviewer judged it better, with a larger heated chamber, easier spool handling and faster acceleration.

    • Four-color CFS printing
    • 350 mm cubed build volume
    • Heated chamber for ABS and nylon
    • Slow bed warm-up
    • Color purges waste more filament than rivals

    Read the full review on Tom's Hardware · by Denise Bertacchi

KeoPrints review

Not counted in the Internet score

Keo's take

Not recommended: Keo's K2 Plus was constantly broken through his time with it. First prints were great, which is what his early video shows, but the long run is what counts.

Pros, cons and the video
  • Early prints were excellent
  • Large 350 mm enclosed build volume
  • Kept breaking during ownership
  • CFS feeder jammed early on

Jan 29, 2025 · Bought by KeoPrints